Search results

A little confused on the purpose for these ports. Manual says they're for pitch and roll servo for gimbal. I got a zenmuse h3 3d and don't see anywhere to plug them in. Are they only for non DJI gimbals? Alternatively it says it can be used for esc 7 and 8. I thought the Naza was limited to...

How to RTF copters (Phanom, etc) get away with using a switch?

Any suggestions for a switch for a 6S 6000maH battery?

Any recommendations on where to place the components of the Naza V2 relative to one another for a clean/dirty setup. In other words which components can I keep close to one another, which components I should give some space, and which I should try to keep as far apart as possible to get as...

I will be using a Naza v2 and have general questions about PID / gain settings. 1. Doing my initial research on PID and I thought they were 3 distinct parameters and therefore would have 3 different settings. 1 for Proportial, 1 for Integral, and 1 for Differential. But it seems like in the...

Thanks. I was actually thinking about using a straight edge but wasn't sure it would be precise enough. Your video makes it very clear. jbrumberg - do you level out your working area first?

Do you attach the motor mounts are pointing straight up (ie exactly 90 degrees of fc or frame) or do you angle them slightly one way or another (either towards center or away from it)? If the former, how do you make certain that all the mounts are pointing straight up and not slightly angled?

How do you store batteries for transport?

If I wanted a dual camera setup, say a gopro for the av and a cheaper camera for fpv what would I need. What kind of camera and transmitter and receiver would I need and how would I switch from the 2 video sources

I just ordered a zenmuse h3-3d gimbal and already have a gopro. I also have a naza v2 with iosd mini on it's way. What else am I going to need. I'd like to be able to view what's on the gopro via lcd screen and see telemetry. Ideally I'd like to use my iPad but if that's too difficult or...

I'm looking for a box to hold everything except the copter and remote. These are the cantilever style boxes I was talking about...

what type of storage containers are you guys using to store your gear? For ideally it would have a combo of small spaces and one larger one. I'm leaning toward those cantilever boxes but wanted to here other opinions

As my name implies I'm new to the hobby myself so take my advice for what it's worth. I am building my first copter and using a very similar frame and build. I'm using a tarot 650 sport. You choose the the motor based on the spec sheets by the manufacturer. Most of the reliable companies...

I want to attach black and red wires from distribution boards with female end bullet connectors. Do I match the gauge from battery? If so anyone know what garage the turnigy nano tech 6s 4500 mah battery uses?

What brand/type do you get of .... ? 1. Wire (brand and gauge) 2. Double stick tape (type/thickness and brand) 3. Bullet connectors (brand and sizes) 4. Heat Shrink (brand and sizes) 5. Solder (gauge and brand) 6. Other supplies I can't think of

I got a set of castle 35A escs from ebay and was planning on ordering Sunnysky V4010 KV375 motors. I don't want to go with the T-motor props right now as I'll probably break a set or 2 while I'm learning.

It's a tarot 650 sport frame. I can go up to 15". I was thinking of experimenting with different sizes. It will be a small av rig. Zenmuse gimbal with gopro

What's a best bang for your buck propeller brand?

Which brand/ model are to be known true opto esc? Also which components are powered by the smaller secondary battery? Is it everything besides the esc and motors? What size should the secondary battery be?

As I understand it they eliminate the vec all together and transmit the signals optically to eliminate noise. Is that correct. Are they always better? Are there certain situations you want to use them and when you don't? I'm building an av rig, would you suggest I use them?