Search results

  1. T

    Can it be bad to INSTALL ESC just below the CF Motor Mount

    Thank you soler for pointing out this. i am still searching the thread but maybe not find the right keyword, its okay will search more. yes have read about this long time ago but limited info's that is why ask again ...
  2. T

    Can it be bad to INSTALL ESC just below the CF Motor Mount

    Hello members, i am about to build a quadcopter. Was thinking of to mount the esc just below the CF motor mount. My point is to lessen the interference to the center frame which i mount the flight controller. Need your opinion guys, is it BAD to install the esc just below the motors... will...
  3. T

    XAircraft x650 v4 with DJI Naza-M GPS values

    Hello guys, could anybody share the gains setting for dji naza-m gps ... what the best gain values you have used so far ... thank you
  4. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    i do it like this all 3 pieces ... 2 goes into the slot 1 mount it front outside
  5. T

    Stock Flamewheel 450 W/Naza Drift's Pulls to the rear

    jckoniecki, thank you for your reply, yes, i also used naza and of course naza assistant software, i also notice the twitching ok i will try this again. setup all and recalibrate then go fly see how it goes. thank you
  6. T

    Stock Flamewheel 450 W/Naza Drift's Pulls to the rear

    are you saying you recalibrating the comand sticks calibration ? just before you take a flight
  7. T

    Low voltage protection

    hi ... ok had made changes, is this setting is okay as below, i am using 3s and sometimes make paralel connection with 2 3s lipos
  8. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    if you want to cut the 4 wire, there is 2 wire with the same wire orange. make sure you mark this first to avoid mistake connection. as for me i cut and joint the wire 1 by 1 just to avoid mistake joint ....
  9. T

    Moved Naza to the center - it flies better

    for my f55o with naza... i use double sided tape as thin as it could be same specs as dji original 3m tape. there must be a reason for that dji supply the thin type not the foam type. foam type a bit thick and may result of the fc not that level even though see with eye its level. so the thin...
  10. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    Hi, for my build, i have extend 3 wire and 4 wire so that the led can be tight at the bracket. what i do is cut the original (3 and 4) wire take another wire and solder and connect between the cut wire so that it is extend. had refer with Eric DJI techincal support and he say should not be a...
  11. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    am sorry, just a quick video with not-too-good quality android camera ... had installed the naza led down at the bracket just a short video about it ....
  12. T

    Low voltage protection

    nisouck ... sharp eye :-) not connecting it to the copter just fill in manually for the purpose of checking but will connect it to the copter and change the value and share here ... thank you all :-)
  13. T

    Low voltage protection

    Thank you very much for advise KopterX will change this value and look how it goes ... by the way any recommended telemetry system ... a link ... thanks
  14. T

    Low voltage protection

    i upload the pics big but it turn out small well load it from another page.. what is the best value to put it ... let says if the batt is all new ....
  15. T

    Low voltage protection

    i am using 3s lipo 5000mah at the moment, planning to have paralel conection into my f550 hexa running with dji naza... can some one please check if the value used is correct in below picture. if not correct please suggestion for me as per explain by KopterX as below: first level protection...
  16. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    here is mine ... done with naza gimbal setting 2x hitec hs-65hb 1x turnigy ubec at 6v as per recomended pitch max 1000 Center -1000 min -1000 roll max 1000 Center 0 min -1000 gain oitch - 23 roll - 23 all other setting is default.
  17. T

    Naza Gimbal problem

    in my opinion the problem is not solved. why roll is okay but pitch having prob. i am too having this prob. naza gimbal pitch ... but in another way yeah it solved your problem ...
  18. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    can someone check if this is correct ? i am using hitec HS-65HB for pitch and roll servo connect to turnigy ubec with 6v ... hurm the pitch travel seems like not good. the roll is okay ...
  19. T

    DJI Naza sub trim

    just to add up, yes i am using naza and have this drifting prob. with just a standard kit seems ok but after adding LG and gimbal then its started. yeah seems that the naza CG somehow probs still checking with this drift probs...
  20. T

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    hi everybody, can anyone using this LG and gimbal controlled by dji naza post a screenshort of the dji naza assistant software for gimbal settings. thank you.
Top