Search results

got all three ready for tomorrow. Just gotta setup the tracker for the plane and i can start packing up. Looks like a party, wish you guys could make it

you want to try and make all your wires as close to perfect length as you can, no extra wrapped around anything, nothing short pulling on equipment. you want about an inch extra in the wire. Solder and heat shrink can make a wire longer or alot of times i'll dive into the actual part and add a...

gains? expo? na ok, manual gains will make it from loose (wont hover in place) to oscillating fast, like vibrating if real high till it tries ripping itself apart. Same deal on any gain whether this, rc heli, whatever you want to slowly roll up your gains and do the kind of flying you do. if...

thanks. I like using it, but riving a couple hundred miles with all my hopes for 4 craft in one camera has me backpeddling to put board cams on everything. couple things against makes you want to film in 960 to get the SD frame when the battery runs out you gotta stop and charge it other...

my old one has a couple pieces of velcro on it and weighs 6.3oz. thought i saw something about 470 gram in the thread at the lab

yep, got a new frame with core pre installed http://www.multirotorforums.com/showthread.php?4958-Kloners-Disco-lets-try-this-again/page2

after my first water flights, RC nut showed me a flotation deal that floats a kilo......... grabbed a couple and i shoulda done that a long time ago. $12 ea, not much bigger than a keychain cam, blows up a balloon and flashes a beacon inside the balloon for 24 hours. hopefully i'll never have to...

should be able to find it if i loose it now....... Gonna take this for maiden sunday too. these are the stories told "As The Glue Dries..........."

You'll get a continuous beep from not having anything hooked up right make sure polarity on everything is right. make sure the wires are all signal, red then black in there holders, make sure none are plugged in backwards, etc I was just setting up a naza and it did this, i had positive...

Fired this thing up, got the osd in core all configured, what a treat, this things the $hit takes 3-5 seconds for the gps to lock in, has 1 watt of 2.4 lawmate,,,,,,,, will be back sunday with a maiden report. So nice to not have gps/vtx issues, and that core, lemme tell ya. makes the 1 watt...

got it sealed up sanded and ready to wrap. next up is loctite 2000 and the carbon fiber wrap. got plans for some graphics though this time camera mount transition came out way better this time

it's scrap.......... you can take that cell out and make it one less cell, but that open cell is junk you didnt get that crash warranty?

mines been in the drink too, i fly over water almost exclusively. never lost anything but esc's. even had my hero2 in there soakin wet. I've found the trick is to let it dry good before getting power back in anything. hero takes a while, once it's not warm from having a battery put in it it'll...

I'd get some shrink wrap back on it and fly it. even a piece of vinyl tape to get by that's a pricey pack

trappy said yellow for 700-900kv motors, green for 900-1000 and the next harder one, think blue for 1100-1300kv. they said they had the guy there figure out what dampened the vibes we have yea, black esc's, the new dji30 amp.... it's all in the details j/k, they were just rewrapped, they came...

thanks guys the green stuff is antivibration pad aka(jello free) from vibrationmounts.com. theres only one that works so if ya need the link, lmk. Tahoe ed is looking for somebody to split a sheet, it's $50ish for half to fly without the case you want a layer lens, it's the thing on the gopro...

The fpv gods shined a light on me yesterday and gave up my second Disco from customs. Got everything swapped over but this time it gets 2.4 video, no external osd and it gets the dji GPS. I sure hope this all works. heading down to painted gorge sunday to try this thing out. having the core pre...

that thing is so sensitive to everything......... doesn't like 1.3 ivdeo either

and i use a polarized filter, think that's like what denny is talking about http://polarprofilters.com/

I'll add i don't balance motors, for that matter quit balancing props but i never fix a motor, if it crashes or something acts strange i replace em,,,,,, there $26 to my door. the props are all graupner as well as the prop adapters. when you make a movie and can hear all four props changing rpm...