Search results

  1. kloner

    my new fpv rig

    This is my third configuration, second version of this setup........ learned alot along the way and the biggest thing i figured out is for fpv, angled flat to angled up is best for me...... but hard to accomplish between the mount and the size you got to work with the frame. this stock gopro...
  2. kloner

    my new fpv rig

    Not worried about the water bit, that's what i bought it for. The deepest parts of that thing are 10 feet, and it always shelfs up to a sand bar or shallows before dropping off again. if i lost it i lost it, but i've been flying helis and planes over it for years and never lost anything. There...
  3. kloner

    my new fpv rig

    yea, rssi on this one too, can't wait. I also built a plane which was the main reason for going so "big" but this will let me get around pretty good. Can move 30 mph using 250-300 watts, gives me 10 minutes of flight so that's what, 5 miles round trip. The desert i fly in is so big, there's no...
  4. kloner

    Show us your FPV Multicopter

    i love em. you know how you drag a nail on a motor and it's smooth or not, well these are as smooth as i can imagine a brushless being, but it took 5 to get 4 clean ones. the motors were putting out 700 watts last trip out full tilt forward with a naza and the motors had a temp gauge, it was 104...
  5. kloner

    Show us your FPV Multicopter

    just rebuilt my fpv quad....... it's got the latest dragonlink LRS system, ET OSD PRO fully loaded. Think the only thing missing is the pitot tube for airspeed. Homemade 433 dipole, shes ready for some long range. Everything twisted this time made a custom mount that gives me 5 degrees up...
  6. kloner

    my new fpv rig

    I've been beating the crap out of my origional frame and decided to pop for a $20 clone frame from rc timer to check it out. The quality as far as stuff lining up wasn't there, but the idea is the same. Got the dragon link, guardian for the OSD to show Artificial Horizon, have problems with the...
  7. kloner

    Batteries in the US

    RTR, nice charging setup. need one of them cases for all the charging gear. Seen these? http://www.progressiverc.com/prc-hardline-cases.html Kill, just make sure there internal resistance is still low if they've been sitting around. little tools like battery checkers have em, shows voltage and...
  8. kloner

    Batteries in the US

    gens ace are the best i've come across. the new stuff over 25c is even better, just came out with these 60c that really hold ir well. there 25c is like a turnigy 40c pack as far as available current and how well the ir holds I've had the worst luck with hyperion packs. Been through 4, all...
  9. kloner

    naza wierdness

    it's how they are. i just go with it and embrace the quirks
  10. kloner

    Just Say No

    that sounds right, 3mm shaft, 4mm thick, 8mm diameter. that's like 25% what boca gets
  11. kloner

    Any guesses what causing the shattering noise Motors or ESCs.

    boca has there grade5 that work really good for this. i replaced mine with them 400 flights ago, still running
  12. kloner

    Must have lost reception....

    like this front is best, that way any turning around you get to come back to you is better than going away, but i'm talking a couple thousand feet. it does line of sight better than my 5.8 video gear, but out of range is out of range. i want miles this is all spektrum ar8000 and jr 11x...
  13. kloner

    Any guesses what causing the shattering noise Motors or ESCs.

    measure em up and order a set. bet the shaft spun inside that inner race and fouled it up, was probably the noise in the vid, like a bushing
  14. kloner

    Must have lost reception....

    I'll bet the placement of the rx and sat had something to do with this. mutley, got any pictures of your setup yes dragon link = good, but has been slow to get ahead of schedule. i heard there gonna open sales back up and ship within 24 hours from here on out, we'll see. There is ezuhf by...
  15. kloner

    Any guesses what causing the shattering noise Motors or ESCs.

    agreed, that's a bearing dumping hard. if you pop the barrel off and stick a shaft into the bearing with a slight side pressure, you'll feel the grit in the one gone bad. can't imagine it shakes like that and not be both or all bearings in that motor I blew out a simonK and it just stopped...
  16. kloner

    MK FPV Quad first outing

    i agree, you want them on different planes like horizontal and vertical. i'd leave the one on the skid if you felt you needed it and flip the one on the arm to vertical, or put the one on the skid back up on the arm with the other one and have a front and rear vertical alignment. i get most my...
  17. kloner

    RHCP 5.8 antenna offerings

    http://www.circular-wireless.com/
  18. kloner

    Just Say No

    mailman knows, mine are different and have a different size bearing. the problem he hit with 2212 was the shafts were in with adhesive so it it's also a shaft, your done and you can't set preload on the bearings because of that, make sure there pressed in right and all the way
  19. kloner

    Grab and go FPV

    i tried down too, but with yuris legs and i couldn't get the antenna under the legs and got shaddowed from them. half the key is getting direct LOS always. i've lost signal not far away crashing, it was the smallest branch between me and it that junked it out. i didn't even know it flipped when...
Top