Search results

  1. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    here's another, just a bare naza flamewheel on 2.4 like you have. it's got 2 sats, both vertical on the arms http://rchelicollective.com/zen/kloner/DJIf330quad/
  2. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    mines like this, never had a problem. glued right to the bottom of an esc, others i've put it on top of the arm. just used a timer and not worry about the light, i fly fpv so never see it much anyways...... you might try on top to get visibility of it grounded without props and running so can...
  3. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    the naza needs to be up against the bottom plate, no velcro, just the tape. That controller flopping around is most likely causing some really weird stuff to happen The IMU, the led thing, put it out on an arm by itself, over an esc is fine. Tape/glue/strap the body of the esc down to the arm...
  4. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    think i see a major problem, what is holding down the naza? the ar8000 too, why isn't the antenna wire sticking out? what is it touching inside? The led module shouldn't be resting against any other electronics. put it out on an arm like your sat was, on top, give it it's own arm
  5. kloner

    GoPro Hero2 FPV video-out problem when in timelapse mode???

    my hero2 has either ntsc or pal in the setup screen I bought hero2 when it first came out and kept getting the timing problem. was in contact with support, they kept telling me to send it in, then would say wait, try the new firmware. 3 versions later, it finaly worked without looking like it...
  6. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    it's in how you bind the rx/tx,,,, you want failsafe engaged and you want over 10% throttle, you see it engage in assistant when you shut off your radio while it's plugged in and looking at the calibration screen With spektrum, you gotta put the bind plug in, turn on the rx, pull the bind plug...
  7. kloner

    after hexa got heavier trouble maintaining altitude

    I ran the 2215 dji motors, 30 amp dji esc's in the 450 with 10x5 and saw 35 amp draws max, hovered at 16-18 amps, 1600 grams, but it was the quad. I'd get the 10x5 graupner mainly cause the 9x5 seem to be gone... can't get em anywhere i can find What do you weigh ready to fly?
  8. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    the big hint it's the dx8 is the total loss of control and no blinking rx's like you saw, that's the exact problem,,,, it doesn't loose signal, it just screws up and crashes your rc if you haven't contacted horizon and told them about this and what your using, you have no idea if it's in the...
  9. kloner

    14 Stiches later, I think something is wrong with my DJI 450 Naza...

    contact horizon, i think your radio is old and needs to be looked at, especialy now. dx8 came out a year ago, when they did, i had 3 friends preorder them. All three started loosing full control of there models to the point they sold em and bought different gear. If you didnt get this thing from...
  10. kloner

    Why chose the DJI F550 over the F450..??

    check these out http://www.rctimer.com/index.php?gOo=goods_search_list.dwt&gcat=142 http://www.rctimer.com/index.php?gOo=goods_search_list.dwt&gcat=144&gtype=
  11. kloner

    DJI NAZA 450 and Spektrum Radio, TX Failure?

    as in failsafe engaging, right? is the ar8000 or sat coming down blinking too? I had my sat like he did for a little while and saw intermitent glitching closeby and could only get 1200 feet, as soon as i flipped it around to the right orientation, it went 2200 feet, stopped glitching in close...
  12. kloner

    DJI NAZA 450 and Spektrum Radio, TX Failure?

    the wires not pointing up down is a major problem..... try it
  13. kloner

    DJI NAZA 450 and Spektrum Radio, TX Failure?

    read this, if that doesn't answer your question google dx8 service bulletin, theres tons of threads on it all. http://www.spektrumrc.com/Products/Support.aspx?ProdId=SPM8800#bulletin
  14. kloner

    DJI NAZA 450 and Spektrum Radio, TX Failure?

    try this, undo the sat, mount it to the side of the arm back near the frame with the wire pointing up and down. one other thing came to mind, is this a dx8 you recently got? do you know if it ever went for recalls? there were 3 i think since it came out
  15. kloner

    DJI NAZA 450 and Spektrum Radio, TX Failure?

    show us pictures of how it's all laid out. where your antennas are, etc.
  16. kloner

    my new fpv rig

    If you ever see one online that looks like would work, link it to me. i was thinking bass boat something or rather. it's never deep, but moves 3-4 mile an hour. a quads gonna stick i think, helis do. planes usualy float off but i got a boat, used to duck hunting and chase birds/decoys all over...
  17. kloner

    motor sometimes spins backward on startup ??

    I've see this too. think it's the motors, and how the quality of the connection at the motor winding is. it acts like one of the speed controller to motor wires is disconnected. i moved a set of dji motors to a different quad than they came on and they did it with different speed controllers and...
  18. kloner

    Very small quad for travel photography?

    follow ibcrazys thread on making cloverleafs at fpvlab or rcgroups, he has all the stuff laid out for all frequencies. Mine came out better reception than what i bought from him....... less snow?, shouldn't be any snow for a couple thousand feet The hardest part of the goggles is if you don't...
  19. kloner

    Show us your FPV Multicopter

    they are fancy
Top