Search results

I tried to used 2 5.8 simultaneously, one from craft to ground station and another from ground station to monitor. When i did, it made everything drop out really fast, couldn't get any range past 100feet. tried several channels and never did get it working. if you run a second in a lower freq...

good question, don't think so. i've only ever messed with hero2 with vtx

i didn't read the thread you linked, but my understanding is two of the channels work fine

i haven't seen any latency in the gopro output. whatever mode you film in you see

if those are 4mm shaft motors, these work without spacers http://www.v-eastonline.com/products/Air-screw-coupling-.html

makes for some fun vids dont it. looks great, flew perfect what are you using for vid receiver? how was the reception. that the windmill or something like that CP? any idea how far you went? how was reception?

you can use regular props on them crazy motors. if there the same as dji, it's just an 8mm prop hub. graupner come stock that way as well as APC rctimer, suppo are a couple cheaper brands, avroto and tiger motors are up the scale a bit

with hobbypartz and hobbyking, when you get a pack you have to decide if your keeping it or sending it back. only way i know how is to use a cell checker cause you gotta do it before you alter it. if you get a pack that's off more than a couple tenths i'd call em right away and just send it...

look forward to hearing what you think on my 28mm motors, i'm settling in on 9" graups seems to peak around 600 watts and the motors come down cool, flights seem steadier, on 4s. Mine likes the 10" with 3s. mid stick manual and mid stick atti are exact, same with the 9" and 4s. the 8's on 4s...

I wouldn't fly a pack with a difference of more than .2v....... that is the sign of super high internal resistance, ie, dead pack. usually if i can't get a pack to hold more than 4.17-4.18 a cell, looking at internal resistance is in double digits. if you did fly it, expect alot less flight time...

this last f450 frame i bought was the rctimer v2. you know how when you build a dji you can put one of the 4 screws into each arm and the rest of the holes line up. well, this one you gotta start all four screws with them all loose just to get them started, then they pull down however. I see...

yes it will eat your bearing flying unbalanced........ crashing does it to. one smack to the motor, usually makes at least one bearing fail. the only way to find em is to tear it down, flip the barrel to the motor around and stick the shaft into the bearing and spin them. if you feel anything at...

some spektrum tx/rx don't like to be fired up very close to each other. you might try making a habit of moving the tx away till it's booted. another possibility is a dirty/loud deans connector making noise. you might take a screw driver and pair of pliers and make sure the spring part of the...

what power connectors are you using?

alot of US shops have the turnigy stuff, but looking around they only show to 18 amp....... I have the hobbywing old school esc's running on a naza and love the way it flies. slight more wobble cause not simonk flashed, but there killer for the money. i took off the cover and put bullets...

better example, manual mode punchouts, see how the craft wanted to dart off to the sides

you'd need a really nice drill press with a vise or a mill to seriously drill the holes perfectly. i think 2 holes is fine, have lvc'd mine from 200 feet up to the ground like 3 times and no problems with 2 bolts. 40ish hours in now but i use blue loctite just for piece of mind Glad to drag you...

what are the gains set to? these have the 16x19 bolt pattern so all four screws go in, but there rated for 3s (though ran 2217 on 4s and they are still flying in another guys flamewheel)...

there 2814's you want to back off the manual gain a little at a time and that'll ease up for ya. theres a point where you want a little so on the flip side of the coin, it is stable when flying around. but if that things wa,wa,wa in on ya, it makes it tougher to get atti setup