Search results

Hi friends - I am thinking about adding the Aerosky X350 Quad to my fleet. I already own and fly other quads and hex's but this X350 looks fun. Currently it links with Droid phones for waypoint flights etc. Does anyone know if they make it compatiable with IOS, will it be a software upgrade or...

Actually tried but having one heck of a time getting the software to download. Think I need a driver or something. I read these things come rightout of the box working perfectly. If a replacement controller board will fix it, I will just replace it. If someone has the links for the software and...

Well I did it and bought a $50.00 gimble off of E-Bay - it has two brushless motors and a BGC 2.0 controller. Right out of the box it powers up and slowly starts to point downward. I made sure the go pro was perfectly balanced as the instructions say. I am thinking the board came out of...

Was out flying this weekend the ole Hex Copter using the DJI Woo Kong flight control system with the IOSD and all was well. Flew in ATT mode and started to see a symbol periodically flash near the ATT. The symbol looks like a little guy running... Has anyone else seen this or know what it...

Hi Friends, Using a Run-Cam 600 camera on my Hex connected to a 5.8 transmitter. Everything works fine however I get these weird pixilation images. Anyone know why or how to eliminate this... All connections are good, batteries fresh an will mostly do it when motion is present. Appreciate any...

UPDATE: I re-read the manual for the IOSD (for the millionth time) and it states "Real time battery voltage of the aircraft power, unit in V. The value is the same as the protection voltage set in the assistant software. blink: first level low-voltage alert. I am suspecting because I did not...

OK - will do more test this weekend and report back - thank you

Hi everyone... Flying the DJI Woo Kong flight controller on a Hex Quad. Flies great so I added the DJI / IOSD. Equally cool but within 1 minute of take off the voltage display (upper left corner) drops from fully charged to 0.03 volts or so.. Of course battery is still strong and flies for...

Hi friends, Just added the Mini IOSD device to my Woo Kong Flame wheel Quad - using a Go-Pro and a 5.8Ghz FPV system. I LOVE it so far BUT the on screen voltage is inaccurate. It starts at 12.5 volts (or so) but within a minute of flying it drops to 0.3 volts. The quad flies for several more...

Thank you very much - I truly appreciate your help. Not too many folks I asked were able to identify the flashing blue LED. Again, thank you for your response and time..

Interesting - I have not run the equipment without the antenna's attached to the best of my recollection. Of course if the antenna was bad then yes I have.. Luckily I still have the rubber duck antennas and will try to use them on a test this weekend. Are rubber ducks specific to a rcvr or xmtr...

All great suggestions and I will start looking for wiring issues and solder board issues.. I know I got the antenna's right and was thinking about trying the stock antenna's incase of of the new ones came defective. Also will try walking craft with motors off. Appreciate the tips and suggestions -

Hello friends, I purchased a FPV system for my Flame Wheel 450 and am using a Go Pro camera on board. The picture is fantastic and clear but when the quad is 25-30 feet away and further the image blacks out for a split second. Both antenna's are correctly polorized, the FPV runs on a seperate...

After I power up the Woo Kong on my 450 quad and as it searches for sat's, the LED will flash GREEN several times indicating home point has been set, however a few seconds after that it will flash a blue LED. The quad seems to fly OK. The manual states this is :Firmware upgrading is finish. MC...

Hello friends - I have the stock Flame wheel 450 with the Woo Kong guidance system, the Spectrum 2.4 Ghz DX-8 radio and receiver w/telemety, a 5.8Ghz FPV system aboard utilizing a Go Pro camera. She flies great so with the exception of a recent weird incident involving the RTH mode and landing...

Thank you guys for the reply - I went back and examined each setting one by one and believe I may have resolved the issue. According to the Assistant, all switches are doing ONLY what they were intended to accomplish, with no additional mixing. In the GIMBAL section I dropped the Manual Control...

Hi friends - a quick intro to what I am running: DJI Woo Kong Controller, Flamewheel 450 (stock motors and ESC), Spectrum DX8, Alware Camera Gimbal and Go-Pro camera. Quad flies well in the yard. When connected to WooKong Assistant 2.0 all values appear correct and functional. PROBLEM: I have my...

I knew about those screens and was curious about if they could be customized. Thanks for the reply.

Hi friends.. Upgraded to the DX8 and am loving it... Have the telemetry for battery temp, battery voltage and altimeter. The DX8 has multiple screens however is it possible to customize what appears on the screen? I would prefer to have a screen that displays the three telemetry values in larger...

Hi everyone.. UPS will bring me a new DX-8 Wednesday for my Flamewheel 450 with Woo Kong FC. I currently am using the DX-7 and she flies OK. Does this procedure sound correct and do any of you have any recommendations on set up? 01). First connect the AR8000 and telemitry devices together...