Search results

I've got a logger on a set of 2215 flying around 1600 gram, 4s, 10x5........ anybody got anything similar with logging on a set of 2212? Could compare Of the top of my head, it was maxing around 400+ watts My take on it is the 2212 have shorter bells, makes them more video friendly, less...

what does your MR weigh? what motor/props? Have you ever tried taking off in manual and flipping to atti? Does it come flying down like the opposite went up? does your tx have throttle trim? where is it sitting when your flying?

whew......... close one. It feels like a computer bios deal but at this point, lets just worry about getting ya flying. This naza is a tough one for alot of folks to get going. I can't see under the naza, but make sure to install it with no bubbles in your double sided tape, the better and...

if you right click the dji thing with com100 and hit properties, then at the top right hit hardware it has properties. click driver, then try update driver, have disk, point it at the driver file you un rar'd........ That's to do what you asked have you tried right clicking the driver file and...

yes, sli, the works........ do you see this in devices and printers? lower left, dji

Have you ever range checked the rx/tx? was this rx in anything that crashed before going into your multi. They don't just automaticly go into fail safe, you have to program it to do it but if you didn't hit a switch accidentaly, i'd expect the same results just trying again without figuring...

having to click skip means it doesn't see it yet. Do this....... turn on the tx, plug in the battery to the naza, plug in the usb, then open the assistant. still gives the option and you have to skip? That solid green light means the naza sees the pc. This is almost like a pc bios issue. Can...

good catch.......... the naza isn't being recognized yet. Try that driver he linked I found a program winrar that let you sample it. was enough to get the drivers installed. The updates so far have all been zip so hopefuly it stays that way. Watch for adware on those rar openers

can you post some pictures of your naza with the wire connectors showing? when you plug the usb to the led in, is the led connected to the naza? When it is plugged in, does your pc show it installing the device by the clock and make a sound?

i'd do it for ya no problem

still in stock all over the US http://www.v-eastonline.com/categories/Graupner-Prop-Shop/Graupner-E%252dProps/

http://www.mikrokopter.us/shop/index.php?route=product/product&path=41_58&product_id=248

the 10x5 are strictly 8mm bore. what size are the motor shafts? can you use like this? http://www.v-eastonline.com/products/Air-screw-coupling-.html that's 4mm shaft, 8mm hub. they have some smaller shaft sized adaptors, but not many of then tighten enough to pinch a eprop. mailman showed me a...

the last comment on that vid RIP Daniel Ahnen who recorded this jaw-dropping video. Tragically fell into a deep glacial crevasse whilst filming an expedition on the Indian Himalayas 17/5/11. Rescue parties abandoned rescue or recovery as 'depth was insurmountable with no end in...

That is usually at the bullet connector. the dji motors have 2 insulating covers on the wire so it is deceiving cause the wire doesn't just come apart from the connector. i finally had one let loose the other day out of nowhere. in my case, when i wiggled the three wires at the esc, the one was...

I recently ran across this guys videos and was pointed to the one where he and his buddy tried splitting the largest suspended bridge in the world. This guys balls are one ring too big, but he honestly seems ok with that

i tried 3s 4400 and with the go pro on it feels sluggish. i've done the same pack without gopro doing bulb shots and it's not bad, but not a racer either. 4s makes mine fun

i run a logger on mine, only watches the battery to the distro ring so it's not each motor, but the apc 10x4.7 on 3s did 28 amp, on 4s did 39 amps. when i switched over to the graupner 10x5 it dropped to 30 amps on 4s, and it barely flies on 3s even without the gopro. i'm 1300gram the fat big...

if they try dingin ya returning them, let me know and i'll give ya what ya paid for em and send them my way. can always use some spares.

I have the 3s kit that came with the 2215 and mine are like i told ya, then mailman got his in the other day and his were wrong. Sorry bro, didn't know you guys got 3mm shafts, mine are 4...... Now i know,,,, he said the 3x8x4 were what worked in his 2212