Search results

that was 4s, but the same mr runs either 3s 4400 or 4s 3000 with no changes it has a slow wobble at worst, but when i'm filming prefer a slow wobble to a crazy wa,wa,wa,wa ride. it hasn't flipped over or even acted like was anything but in control but yea, looks weird not in fpv. better you...

need to look at shielding, connectors, the power to it, that connector, and if all else failed, try powering the lrs from it's own power supply, like that pack with the servo you used..... Somewhere somethings dirty. Does the wkm sat antenna have to be in the middle? If so, that sucks. they need...

i run mine 130-130-120-120 and atti is 80-80..... You want to run it in some wide open punchouts and drop your gains just down below oscilating. Easiest to see from on board if ya can. watch this vid, shows what your looking for, any shacking or wobbling needs tuning. slow wobbles are too low...

heres the pics of the quad Wound up changing the camera to a gopro case with a dampner had laying around to help the jello when it flies in the wind. did alright. Gonna try 9" props next to see if that helps anything. Got 8" came in while was gone too.

love the shape and size, but the power distribution sucks. had half the interference with the regular plates. In the wintertime, that things so full of decoys and hunting crap you can't even walk in it, that's a 12' boat sitting inside the front and 100 duck decoys. my other habit

Went to the colorado river over the holiday and battled my new frame build most of the time, but it kinda didn't matter cause the wind was howlin. we started out tuesday it was 112f and the winds blew 10-15. next day 108 and it jumped a bit to 15-20. by thursday we were in a wind warning of...

uhf isn't as easy as plug and play systems like spektrum/futaba. There so touchy to any interference......... i battled mine for a week and finally am coming down to figure out it's 2 of the deans on my packs make noise..... Anything that can cause interferrence will. Even a noisy motor, bad...

DJI is printed on the center plate top and is in the mold on the arms. The clones don't say anything

hero2 has only been out less than a year and has a year warranty, unconditional no questions asked i believe. straight replacement, no fixing anything good to hear. i just make a alarm beep tone at mid stick so i know when im at midstick......... that way when you do get blown down or up and it...

this guys been nothing but a pleasure. last minute buys at night still hit the mail same day and it's free shipping usually http://www.gothelirc.com/shopdisplayproducts.asp?id=133&cat=DJI+Multi-copter

charging batteries we use a term of a charge rate as in 1c, 2c, 5c, 8c and that's about all i know exist. if it doesn't say the charge rate, assume it's 1c. That said, 1c of 6600 mah is 6.6 amps if it said max charge rate 5c, that is 33amp max amp charge rate. However, those high charge rate...

you'd think it should, but i bet depending where you have the voltage cutoff set to that pack was already damaged when it landed. to seriously take care of flight packs, you gotta use a timer and you gotta make it early enough that you know damage can't happen. seriously, 1 second to long and...

When you calibrate, your not so much looking for the green bar to be green, you want your throttle stick at exactly 50%, like you made that switch. You hit "start", move all the sticks around moving the throttle to exactly 50% and hit finish. That makes naza see mid stick......... you have to...

i use one gain wire and got it on a switch assigned to gyro channel. i leave the manual gains like above, but have atti on the switch. when you set it up, put the gyro gain to 80, goto assistant assign it to the x1 or x2 and type 80 in atti mode, now when you move that ( i use 70-80 and 90) it...

best money you'll spend in the hobby. if you give it the full input rated, it'll fly through 6 packs. i paralel charge 6x 6s 3amp in nothing flat, but it also has the dell server 24v 1500 PS. loud little bugger, but nasty fast and more importantly, very consistant. keeps your internal resistance...

Did you guys notice the flamewheel pricing,,, check it out http://www.dji-hobby.com/flame/index_en.html That's not much more than the clones.....

what about the sponsor here, maytag? I like castle stuff in my single rotor helis, but the HW pentium at least in the larger ones are the most desireable for fast switching in v-bar governor instalations..... Saw a post a while back from castle that they were working on firmware to make them...

are you guys talking about the width or depth? you can change the depth distance mounting any of these in goggles. thats the fatshark predator with built in rx. heres a thread on another set http://www.fpvmanuals.com/2012/05/08/carl-zeiss-cinemizer-ski-mask-build/

wow, you can't wrestle it back to level? how bad are the vibes? vibes would make stuff like this worse than no vibes. would love to see a recent on board video, see if it sounds or looks worse than when you started. Both mine are a little quirky, but nothing to make me stop the motors midflight...

you did that when you bought a clone.......... haha no big deal, lets see whatcha can do my quads got the Eagltree gaurdian only for an artificial horizon, i noticed it does the same thing in it but the quad recovers way before the guardian. must be how the vibes increase from the motors reving...