Search results

either your settings are too aggressive or your pack isn't the voltage you think it is. need a voltage of your pack, it sounds smoked

also make sure your 3s hasn't become a 2s by overdischarge. use a charger or voltmeter to look at the voltage, should be 12.6 fully charged

this sounds like you have the voltage protection enabled and set to 4s............ go into assistant and disable the low voltage protection thing.

yep I ordered a set of the 2814 1000kv suppos last night for mine. gonna switch back and forth and get some data,,,, see what the difference is on the same bird

I'm wondering about the osd part too. mine is logging 1.5 times the amperage it sees, but mine doesn't blur or get hot. The first frame i burned was from a solder too close to another solder and it finaly burned the trace after i just finished flying it. but, even with the osd being crap, the...

your ready

just because it's a switching regulator, wrapped mine in aluminum tape and shrunk wrapped over that again

I tried two immersion 5.8 on total other channels and i had a greatly reduced range, like 200 feet was fine and it shut off at 220 feet. i'm not sure if the different types of boards will work any better. let us know what happens, it's obvious, good part is just kills the video reception and not...

looks like a heli guy did the wires.... hahah looks good That paper comes off your layer lens. it's just that stuff to protect the plastic as it's machined is there any logs or captured osd to see how them motors eat power? them are probably my next purchase.

they emit noise too but they work with the dji gps http://www.rcgroups.com/forums/showthread.php?t=1422899

i'm suppose to look through your pc and know you understand everything.... this is makin more and more since. all i remember is you have 30 tries to make it happen, in between those tries it works after you cancel out of the window your stopping at. since your programing smart and not hacking...

I just plugged mine in and hit firmware assistant and it logged into there server and did the check...... about 4 months ago when it was there server, even plugging it in and turning it on after you registered got me that same error you guys for sure are online when your trying to register it...

I've seen 500 watts on atti, 730 max in manual in the 2814 with 4s and 9" props, when i ran 10's it hit 900 watts. according to my calculator that's 56.25 amps

heading out early next week to maiden v.2, shes totaly ready other than the pixim cam is in the mail so gopro live feed it'll be. got the first 1.3 helical under my belt, kinda big for my current tracker, we'll see. 10.35" long, 3" diameter, 9.85" baseplate. beast 4 1/2 turnheli

zeph 2 runs 2 of the 3000 4s in parallel, flies 30-40 minutes running one of the 4000 4s in the back of my disco used to run 2 of the 3000 4s on my kloners fpv450 but just sold it The 5000 packs used to fly on it too, but now there dead weight, nothing i have anymore carries them. over the...

http://www.hobbypartz.com/98p-25c-4000-4s1p.html Thats the goin rate for any brand that size. I just got some blue sky from that place and the internal resistance almost didn't exist. honestly lower than any gens ace i have bought from them. but there all the same price, and as of yesterday...

i've got both, but a few of these i wanna hit are only accessible by boat and there isn't always a landing spot other than the deck of the boat. the big one i'm after is called Picacho mountain But yea, i'm into flying places, usually i'll go out and do a mile and back, usually eats a pack...

i guess it's all in what you want. long flight times aren't my first priority at all. I want to go up mountains and surf down em as low as i can, it's all i got in my mind. to do it anywhere near right, those horrible flight time motors are needed. Alot of guys with these are running 40mm...

Koom, yes that works. That was how i used to do my failsafe bind and it failed safely alot, just be aware it may go to one side or the other on ya without knowing it cause there is also either endpoint right to the side of floating the switch in the middle but before it actually clicks

my mistake Part Number Description Sell Unit Quote Quantity Extension V10Z62MSN05 Silicone Gel Pa Each $85.19 1 $85.19 Sub Total: $85.19 Freight: $10.03...