Search results

just less crap, more power to fly further if you got weight and room to spare, put a pack in for flight..... I'll burn 6000 mah, takes me a 1/2 hour and wheni land if it used a spare battery, would have been like 200 mah, 800-2000 spare mah left over. Even when a plane battery goes all the way...

if i turn on my naza without a radio, it goes into a beep, beep, beep. that means it doesn't see a radio signal through the servo lead........ it could be inside naza, but not likely. it is usually in relation to the bind of the rx, a rx with an incompatible sat attached to it was my problem...

the 2216 are rocket ships and still "small" doc, theres sucha difference in weights and what you carry, it all comes down to what you got, what it weighs, etc. out of the box, the 4s 8" and 3s 10" is about spot on. add anything and you start changing alot of it to where you work back to mid...

what were you asking max?

same one the video is from above but mine is 2.8mm, the one you link will have a slightly narrower field of view..... i think the 2.8 is 120 degree fov, same as an eye. Got used to flying with 170fov on my gopro so the 120 was a releif

depends on the vtx..... i use lawmate,,,, it is a 12volt tx, but runs better down around 10.5 volts, less noise, heat, etc..... immersion stuff doesn't need anything al all, it has built in regulators, has built in filters. all the rest of the brands need everything 12 volt, no choice.

it is best to run it all off the flight pack, through regulators and filters. if you run a 3s pack, filter is all you need, like this http://www.dpcav.com/xcart/Power-Supply-Filter-L-C-Type.html if you run 2s you need something like this...

I've only tried 2,,, both securitycam2000.... on is the ccd hadII 600 line and the other is the 690 line pixim, the base of the tbs 690 without the tbs firmware and i really like the pixim alot better. the ccd has a .01 lux and the pixim is .1 lux, but the looking at the sun in the pixim is alot...

theres a little clip yo can peel out and the shield comes off, but you need like watch repair equipment.. even in a big bearing like single rotors have are a pain to get apart. The bb's in these 22mm motor bearing are like grains of sand,, smaller actualy

it's all experience... the good, the bad, the ugly i can imagine them frigin vines. At least there all dying soon anyways so couldn't have hurt em too bad

probably do...i can hear predator drones over me the whole time i'm there and i've gotten to the point i don't think i'm the threat. there scouting all around me..... in the zII on the tracks video, if you pause it at 1:21-1:22, thats all mexico. There is a faint black line half way to the...

I know, but your looking at boca, the only high end marketed bearing place in the us that i'm aware of that gets top dollar, hence they make parts for high end stuff. When your over here at boot camp naza, were just throwing crap at the ground seeing if this ir that works....... not even flying...

the closer you can get it propped to carry your load at mid throttle and hover in manual, the less of that wobble you'll see. if it's wind related, use smaller props and more volts.

i hear ya,,,,, when i got going here, my old style dji motors all got replaced with grade 7 and after that, i never had a hot motor. they were some crazy $8 bearings or whatever. But, the next guy that came along with a modern kit,,, the frigin motors shafts were loctited to the bearing race so...

in theory if everything was what we thought it was, as in greased with a high end material, i think he'd be spot on. the lucien he speaks of then us saying scorpion taught us is one in the same and i think irritating the piss out of him. Lucien is the president of my ama flying club, lives a...

dam dude, i heard a prop leave or something on the first one. That different pitch it made after the jolt, thats a motor spinning without a prop that second one was friggin cool You couldn't do that again if you tried. i always wondered what would happen if i hit one a while back i stood on...

they grease em everytime i get the oil changed,,,,, my boats wheel bearing on the trailer are oil filled, you can see the oil float around the clear cover, you use that or bearing buddies which are greased, but the same thing, a sealed ressivor of grease I hear ya, but coming from rc like alot...

tell me about it

mine shown are suppo bullets

why they use that channel switching thing? been around this a little while and have enver changed the channel on the ground..,, that antenna is gonna get them in the same trouble immersion is in with ibcrazy, it's pateneted i thought the same as you pling, but if is the case, there aint many...