Search results

it is an analog output, typicaly there is a ground, video signal and possibly an audio signal. usualy power is a usb adapter if it's the hdmi2av but the nex powers the hdmi cable so it shouldn't need power... if it's not this type, get us a picture typical is red = +5v, brown = ground, mustard...

that is frightening... it fell at terminal velocity for a minute,,,,, how far up think it went? couple thousand feet easily... crazy man, crazy

mine bolt on short 6mm hubs from Aerial media pros.....

dam, they drifted right over the pad on the decent...... that grasshopper is cool stuff

that seems a bit extreme of a test.... if you fly the cf props, get the other type that are flat across where they bolt like Tiger brand, not with that narrow hub like shown

careful flying on oxy..... I have had several surgeries the last few years,,, i physically take my models out of my house so i don't get any bright ideas. Even after your off it takes me a bit to get back on the ground mentaly..... just be careful. My dads spare bedroom sleeps alot of models...

were using 16mm,,,,, can get from anywhere, think it's a trex 500 tail boom..... hobbyking has the tubes for a few bucks ea

900 kv 4s stock length setup..... 400 kv 6s extended length...... with the shorter version there is zero flex in any three axis, the extended ones have a tad bit of radial flex, but none x y....... guess a higher end tube might help, maybe even aluminum tube like a tailboom One things...

there is some monitor mounts on goodluckbuy that are pretty neat and almost like what he has there http://www.goodluckbuy.com/fpv-7-8-monitor-mount-holder-display-support-folding-carbon-fiber-for-futaba-jr-wfly-transmitter.html then vrx and it's battery back behind the monitor........ just...

radian, but it's a tough mount..... alot use it on the roll only and leave rsgs on tilt/yaw...... look into the brushless conversions, that's the future and money spent in the right direction

black dampers and the gh3 i believe raw av200 and gh3 on yellows

that would be a question for jcmonty..... i just tune and fly the top part..... it is a gh3, about the extent of me understanding cameras. he uses alot of some kind of auto focus cause in low light that thing bounces around and ruins a shot from time to time, alot less in the bright light the...

i like what he's got there,,, the electronics themselves just being in proximity to the radio and kill range on both. Do a low power range check with everything on before you fly..... watch the led if dji, watch for it to go into failsafe walking away from it

on 20 amp hours of p6s it does 12 minutes hovering, 9 minutes of booking around chasing stuff the black dampers are the similar durometer as the yellow, they just don't flex around and let the cam shake as much....... we were addicted to teh red ones for everything because of such and my crazy...

I like the tiger 3520 on 15x5...... does gh3 to reds all with same gains, same setup... only thing we swap is the gimbal that is always setup per cam.... the new black damps are better than the yellows for the gh3-dslr

that vrx is aluminum and not very rf transparent as well as a little noisy...... try getting that away from the tx antenna, like at least 20-30cm, not letting it lay against it.....

and it works perfect.... way better than the copmplete slide on like you guys show.... We fly this thing 2-3 days a week, gimbal off several times a day, absolute perfect footage from the three gimbals that ride it..... I also have it like this on a disco and a hex, way preferred imo. don't see...

weller wesd51 does it all,,,,,,,

ground is common in the whole thing..... you should be using a ground and a signal to make it work right...... the 5v out on the immersion is enough to run the hdmi converter, at least the freefly ones. we have alot of probs with that kind at kopterworx, might be from using that 5v, might not...

17*12*6 there the bolton hardware clones from ebay