Search results

you want to run it full manual if you understand it and can set it up right......otherwise, send it up for some scene shots and see how it goes. I'm an automatic guy..... landscape works good, that sunset mode is amazing if your not into properly exposed footage that looks cool. can't see the...

thanks for the nod Chris We do pointclouds with lidar on uav's that looks like this

http://on.mtv.com/168rUhi

Boris, just watched your vid,,, your getting a tad bit of the bounce,,,, what dampers and what kv/props are you running? is there any pre load in the gimbal bottom mount?

where are you located?

bart has some prefabbed ones at aerdro.com,,,, everybody is starting to head over to hd downlinks so the freefly one is a hd router now.... movi and all

anything except tiger are super flimsy and make alot of cavitation..... not saying they don't work, but there alot different than the real deal.... I fly reds on skyjibs so i'm super picky about that kind of thing. We did some testing with AMP props and there just not the same, neither were...

the servo goes to the droidworx control board, it is pictured above..... if you want to use endpoints to control where the servo stops you gotta use a servo wire straight from servo to receiver and bypass that board we use a seperate bec so if the servo geeks out it won't surge in the flight...

some people run the way the gear comes with the controller handling the servo stop points, others bail the board and go to end points. i run the droidworx controllers on both with seperate bec's for the retracts

here are the other files i have and use www.kloners.com/EzUHFFirmware_v1.44.zip www.kloners.com/EzUHFFirmware_v1.43.zip www.kloners.com/EzUHFFirmware_v1.29StdAndUK(1).zip www.kloners.com/EzUHFFirmware_1.40e_WithIRCTools.zip

boris www.kloners.com/EzUHFFirmware_v1.44.zip www.kloners.com/EzUHFFirmware_v1.43.zip www.kloners.com/EzUHFFirmware_v1.29StdAndUK(1).zip www.kloners.com/EzUHFFirmware_1.40e_WithIRCTools.zip

were pushing on this project as hard as we can. they ordered 10,000 pcs so the ramp up to production and samples have been slow coming but they promise once we hit go it'll happen really fast..... i appologize for it taking so long, my analness in perfection has gotten in the way of it being as...

i'd do 50-60 amp esc's if you fly in heat much,,,,, 40-50 if your in the cold alot.....

i bought 4 of them servos when mine stripped from mishandling it...... i got these gear on 2 rigs and 6 months later there is still 3 new servos in the box. once you get it working and don't screw up, it seems these servos are plenty.

smallHD are pretty popular...... i haven't seen the monitor at AMP yet

i've setup 8fg too but i too had problems getting it going. The number one thing i've done on both radios is open the futaba trainer chords bottom pins so there is no ppm going from ezuhf to the radio pin or voltage on all of the futaba radios i've built. when that clip is open and we call the...

these servos are easily stripped. if you ever heard it click when you were building, that was teeth leaving yea, super cheap servos http://www.wholesaletrains.com/Detailair.asp?ID=200859363&gclid=CIu_y8u_uboCFcU5QgodKD4A8A but once you get to using the rig they tend to be easy to keep alive...

i stuck with an older firmware and it works great,,,, been 18 miles away and more rssi than video signal....... too bad i'd avoid dragonlink and go straight to a sherrer system but usually the problems i've seen in others was easily fixed with a new futaba 8j for $270 with the ezuhf on that and...

we use the triggers on this stuff and it makes for alot less mess to sort through at the end of the day. At least it's just the best attempts you had instead of a bunch of just getting on scene and little meat in the middle http://www.rcshutter.com/

scrubbing in