Search results

I updated the firmware on Master imu, and if i try to update the Slave i'm unable because when i power on the fc don't update it automatically like i do it for the Master...any suggest? my seller says wich is normal, the slave don't need to be upgraded

My coaxial x8 is equipped with U8 motors and 28"props..my main problems is the losing altitude!! Especially when i go forward of when i use the yaw I tried all the gains but nothing happen! I can adjust all the gains with my knobs..but nothing happen. We are talkimg of Devourer x8 from...

Yes, my GH3 camera is PAL, and i set 1080i as video out..and i tested also connecting my monitor directly into the video out of the zenmuse CGU, my video is DOWN always, and came back only if i touch the hdmi converter board and the hdmi flat cable...it could be a bad connection or faulty hdmi...

I tried all the 3 different configuration of the Zenmuse, but nothing change! With my second transmitter, i assigned the TILT of the camera on the left stick, when i try to move the stick, the camera move it untill i'll not move again the stick into the opposite direction! This is very hard to...

I would like to use a second receiver to control the gh3 gimbal with another operator...could somebody help me? wich wires i need to use? how to?

Registered UserJoined Aug 201034 PostsCould somebody help me to improve the pitch control feature of my gh3 gimbal?I fly with my lumix gh3 and gimbal zenmuse gh3, with one piot mode, with my LD potentiometer of my futab t14sg i can control the pitch of the camera, but movements are not...

Having problems calibrating the compass. I have flick the mode switch 6-10 times, but the light won't go blue. Is there anything i am doing wrong? my 3 switch is set to GPS, ATTI, MANUAL, i tried 10-15 times to switch it...nothing!!! the BLUE led wont coming!!

Could somebody help me to undestand how to fix this strange problem? Sometimes the gimbal make some strange movements..especially after a yaw movements of the air craft, is something like a "bounce" for a 4-5 seconds..I'm using a single pilot, so the PAN (or yaw) axis is automatic. Here are the...

This is the first flight with this beautiful machine, 2x batteries 6S 5900ma, take off, and after 20 seconds the red light is flashing..(YES, batteries are FULLY CHARGED), i think the default voltage setting on wookong software is wrong..any suggest? i'm too confused about the voltage...

I hope i'm on the right way..what do u think?

I'm using the 7008 receiver, assigned the LD potentiometer to control the pitch of zenmuse, but everytime i touch it, the camera moves untill i touch it again to 0 positionto fix it the new position..i need to move the potentiometer one time only..any suggest?

where should i connect the landing gear IN servo cable? and wich switch assign? i have a Futaba t14SG with 7008 receiver, on D mode!

It's a strange noise from the roll and pitch motors, any suggest? here is the video https://vimeo.com/78812995

I need to connect the GCU of the Zenmuse GH3 to the wookong controller, and to control the pitch trough a potentiometer on my T14SG, could somebody help me to give me the istructions of the wiring diagram? i'm using the SBUS connector of the Furtaba receiver to the X2 port of the wookong...

I have a s800evo and now iwould like to use a canon 6d with a brushless gimbal, can this machine lift this setup? What kind of batteries can i use to get more minutes with this wheight?

I would like to buy the Tarot T1000 IRONMAN with a good brushless gimbal to lift a Canon 5D mark3 for video shooting, is it the right choice? Where to find with cheaper price? Anyway, could somebody suggest me the best combination of motors/props? Thanks!! R

Hi to all!! i'm Roberto from Italy, owner of a F550 multirotor with gopro hero3 and brushless gimbal, i'm new with multirotors, and i would like to share my expirience with others! ciao!!:nevreness: