Search results

supports y6 now, everything else looks the same. Anybody see anything i missed?

mine was showing up in the live feed too. Yuri, update the firmware, if you did and it's doing it, there gonna want it back. contact support, it's kinda fast

that above was sent to gopro support, they had me update the firmware to 2 weeks ago release, it was doing it half the shoots. After firmware it didn't do it for 30 clips, then it did it three times in a row again, i gotta send mine in for a look, got the rma yesterday one thing i notice is it...

thanks for the intel, does using lower resolution help the cmos glitch? yuri, look like this?

it sounds undergained, but like said, no wind. Best way to see it is with the gopro vid. when you hit too much gain it gets real throttle'y rev,rev,rev. when it's under, all i see is a little wobble and a drift. the lower gain range makes better vids. I fly it pretty aggresive and been letting...

When i use the fatshark goggles, there 4:3....... using the hd modes makes the top 1/8th and bottom 1/8th black like letterbox. When i'm filming in 960, it fills those areas and makes a more up/down view kinda nice so far when i tilt forward to fly or come in low, can see the ground. Is 960 the...

that was pretty cool, sure looks different than here check this one out

plug the usb into the led/bec, plug in a battery to the quad, does the computer make that sound like a driver is installed, it's like a 2 note beep and by your clock should say dirver loaded or driver unsucessful You might try a different usb port on the back of the pc if theres one available

awesome.....

you snip off one wire right at the base and solder it up to the deans, after i got the heat shrink placed, i do the next wire. You kinda need a hot iron, if you don'[t have a nice electric, look at them disposable propane, there hotter than hell. I got this one, tins 8 gauge in about 10...

I have the same problem with 10" props and 3s right at 1100 grams, went to 4s and 10" props and i'm still at only 10 amps a motor average but it has all the extra power you want...... this was thw 3s kit. on hot days the motors are warm, not hot and the esc are ambient. check out this...

i have 3 of these in my ride you've seen the videos of after crashing. It's a big deal, you want it fixed even if it's a spare for next time. grade 7 http://www.bocabearings.com/bearing-inventory/Radial-Bearings/2337/SMR84ZZ7-4x8x3

looks like 5.25" long or 135mm

those 3d formations are wicked looking anybody got a recipee of parts to build something like those? like what size motors/esc

it's a really small tick,,,,,,, just be sure cause they die fast when there screwed up. starts rattlin and screamin

this place http://fpvlab.com/forums/forum.php

that's a bummer. if a motor went in, you should pull the c clip off the bottom, slide that barrell off and stick the shaft into each bearing, with just a little pressure spind the bearing and feel for dented races. it'll be a bump or a tick. if you find some, get some grade7 4x8x3 bearings...

that's awesome. Somehow you'll want to balance the props in your kit. kinda tough cause the hub shape, but that's what makes the difference...... especially with a camera on there but even without, the thing smooths out so nice. if you can afford it, get a set of graupners, there in stock now...

your onto something with the throttle part of this thing. flew sub trimmed like mentioned 2 flights perfect, third flight got all drifty again so i took a look at the throttle deal and put my subtrims back to center. when i make 50% on my throttle stick centered and green on the assistant it...

You want - expo on futaba to make center slow, + will make center stick faster with small movements I didn't touch the throttle subtrim in the assistant, i "subtrimmed" ail and ele. My throttle was so far off i left it. Hands free hover now. theres a beep set on half stick on my tx, it holds...