Search results

blue is the normal threadlock. comes off without heat and holds really well. green is usually a shaft to bearing collar material so shafts don't spin inside the collar. red is way overkill, takes a lot of heat to soften it enough to remove liquid version is best, put a small dab onto a piece...

anybody know where a guy can get a frame only for msrp? don't know why, everybody but foxtech wants $19 over msrp if they even carry it not arf..... but foxtech wants $25 to ship it.

Whats up Dr Tim???? i met you up at scale masters with the grapd/gjive md 500 and 900..... Yea, your the real deal Do you have any footage on youtube? What servos do you run? Good to see ya here

that's that setup in manual till :18 sec then atti....... super stable, flies good. but it has 28mm motors couple weeks ago it was like this and it flew/filmed like this that zeal did a good job, could take it to 1080. but i put a strap over it when i took it ftp and it translated some...

My immersion 5.8 600 went 2000 feet before any junk. What is that layer lens? Is it on a hero1?

You didn't cut that groove deep enough, I can point mine up hill 10 degrees if wanted

I've run 2 different configs of the gopro to the f450, both are working good. The key to keeping it rigid on a tab is to use the short tab like ski recommends the bottom plate oriented and to get the mounting bolt as close to the arm as possible. The other way that worked was to get a set of...

did you calibrate your esc's one at a time?

Mine is an f450 Flamewheel frame NAZA controller DJI 30 amp esc's Suppo 2814's graupner 10x5 Hero2 immersion 5.8 600mw Eagle Tree OSD PRO Logger v.3, GPS expander She flies at 1625 grams RTF, with the 4s 3000mah packs, i get 9 minutes and with 5000mah 4s she goes 14 minutes. Last weekend was...

i've tried form 9"to 11" and never seen any difference in startup speed all on 4s.... are these DJI esc's? Does your throttle calibrate clean in the assistant window? moving throttle to half stick when you hit finish in calibrate? got the throttle trim in the middle or disabled?

I've only ever seen these so there all i know, but when i used em they had a great picture, but the fit to my face sucked. built these last night, sure hope it makes it less stressful. one thing i noticed was when i'd take the goggles off, it was like walking out of a movie theater in the middle...

this is what the 960 mode intercepted by another rx into a 65" projection looks like. it's probably the tv cropping it. dunno, kids ate the remote so can't even see the menu anymore the goggle show full screen SD 4:3. kinda like it, can see better especialy tilted 45 degrees forward booking...

tri flow here

mine has been doing that and has been registered for 4 months...... try hitting cancel when it wants you to recheck the registration. I think you only get so many times though, so go easy wonder if anybodies told dji yet?

take a motor and give it a light push/pry and see if you see any cracks in the frame around the motor. do all 4

try putting your gains back to 100 on all of them are the props balanced at all? do you have any expo programmed get us pics of the airframe with the props in view

After last weekend it was obvious i need a better way to keep the monitors in front of my eyes. the raw fatshark frame sits in one place on your face, and it was angled down making it really hard to see, felt cross eyed while i flew, was stressful. So, got out the dremel and blew a mounting hole...

better reception. was getting deflection from the props down low yea, remember the kit we got........ lol the big motors are where it's at for what i want. This is gonna be fun

looks great..... it's in 960 mode so it's full screen and super clear. looks like the fpv videos that came out of it that i posted. whats suppose to be it's problem?

from those legs. 20 mph winds with the cam and legs sticking down were pretty in efficient. stable, but slow