Search results

cool, no problem. if you get confused, hit me up this looks like a party waitin to happen. 4th of july is gonna be an airfest

whats in the ipower for bearings? did any come not smooth? or is it a crashin thing? They are both fast........

hmmm, my 1000kv needed 4s to really "go" this was 10", 4s, 1000kv, 1680 grams on that fpv rig

what do ya run, 12"

I mis spoke about the eagle tree one,,,,,, all you'd need is a logger and gps module like this http://www.readymaderc.com/store/index.php?main_page=product_info&cPath=10&products_id=143 http://www.readymaderc.com/store/index.php?main_page=product_info&cPath=10&products_id=123 it makes maps...

to do what your asking is in the fpv OSD's like eagle tree, EZosd, Dragonlink OSD, and probably a few others. each of them would have to be put together except ezosd by immersion. The others need seperate parts that add up like gps module, barometric altimiter if you want real heights for the 3d...

there made by graupner...... $3 ea. the motors are $23, props are $10. when i crash, and i crash alot, any motor that breaks a prop just get's replaced and all the old crap thrown out. used to try rescuing them but for that money, it's cheaper and less stressful for me...

sounds like you were in manual mode or like said above, not enough gains. I've never had good luck with just setting atti and taking off. both of mine acta ll weird and disconnected feeling. i spool it up in manual, then flip to atti at speed or right when it leaves the ground. major drift could...

the rc side quads EZuhf zephs dragonlink

thanks, monitor

I run graupner 10x5 and 10.6 and the motors never got within 100 watts of max watts with the 10's...... no dis. backmount kit? there 19mmx19mm mounts heres a log of said combo in amps, that's split up between 4 30 amp esc's and 4x 350 watt motors.

Think it has to do with the motors fitting the weight and using the 9's. i've got everything ready to swap all this straight over and gonna switch up to the 1.3 vtx then. needs 12v i don't have to offer it now pretty much what you got that multiwii place is about $3 less a prop than here...

i get 10 minutes on a 4s 3000 mah pack, and still got 800-1000 mah left....... My frame is in customs, should have it any day now. Where are you at? theres still a little jello, but it aint bad at all. definately fpv approved!!!! i hate flying in 1080, rather use 960 for the top and bottom...

love these http://www.altitudehobbies.com/brushless-motors/peak-suppo-motors/brushless-motor-peak-480-35-36-1000kv-suppo-2814-8

http://fpvlab.com/forums/showthread.php?5371-TBS-DISCOVERY-New-quadrocopter-frame&p=109914&viewfull=1#post109914

according to trappy, any foam setup will tame it to 720, but if your after 1080p with the gopro, you need that sheet. only need half, wish one of you guys wanted it in the usa, i'd split it with ya

might try turning down your gains some too. really high looks good from the ground, but makes the vids kinda weird and i bet your mileage down the drain from over-under revving the whole flight. heres the gel link from trappys post...

try a set of the 9" props...... they drop the watts all around by quite a bit. mines been carrying 4s 3000 on top and 4s 1800 insideand she goes 16-18 minutes depending how far forward i push the cyclic in atti. it'll do 30mph with 300 watts or 45 mph with 600 watts on 9", 10" was another 100...

castle ICE is supporting multirotors now with the whole 400hz refresh, up to 8s when you don't use the bec, 6s when you do haven't tried it myself, but a couple guys i know are running them

most likely. When you calibrate, try starting the pc to calibrate, roll all your sticks around exept when you stop, put the throttle stick at dead nutts middle. look for a monitor to see where 50% throttle is. leave the throttle there then hit finish they should all four light up green