Search results

The 2 antennas on the uhf are the rc control. Being sanders style, they like to be straight up and down. Got one for medium forward flight standing straight up and another on 45 degrees for full forward flight. You see the rssi bounce when it switches antennas as i lean it forward. The...

you need a naza, welcome to the habit

Probably, wanna see how that pans out with others first. I've been having a heck of a time finding a sweet spot for the ET sat ant. thing gives me a fit every trip, tracker stops following on my other rig. dunno if it's the solar flares or my setup. seems like everytime before i go the news...

Just about got her done. still needs esc's and a camera. Went with the securitycamera2000 pixim 690, like the tbs69. dji esc's will be here tomorrow, i'll test fly it then. this thing is noticeably lighter than mine in hand, by alot. Think a friend wants it, might sell it and do it again

those motors with the built in prop adapters start causing problems too as you crash you way through learning. any moarks usually makes it not accelerate/decellerate as well as it did. same with dings in the props

man, what a mess. i don't have gps so i'm not used to what it acts like, but to me it looks like when you let off the stick it tries to stop it making it wobble. have you tried just flying regular atti yet?

is that in atti?

video of it flying at 130..... i'm curious what "pretty unstable and shaky" looks like. is it like water going down a toilet bowl or bouncy/twitchy? fast or slow? either case, once i got down bellow 140's mine pretty much quit all it's bad habits

you should be ok at 130.... got any video of it? from onboard would tell us more.

keep an eye peeled here http://www.rcgroups.com/fpv-rpv-equipment-and-vehicles-fs-w-710/ alot of this gear goes through there

got any pics?

We look forward to your adventure! when you get this flight controller mess sorted out, let us know your fpv questions

the motors spin such low rpm's for there kv they can't speed up fast enough to counter the wobble. if you have a 3s battery, try it even if it's small, just hover and land with the 10's a bad bearing will start to show as a wobble too. make sure none of the motors are hotter than the others

forgot to answer the water on stuff question....... no it shouldn't make the flight control act weird. what it'll do is smoke the esc's to the point smoke comes off em and the motors never spin. I've soaked nazas twice now and never seen any lasting problems. metal, wood, debris is bad inside...

you guys should try lower gains still.......... if your seeing a fast wobble from onboard like was in this youtube above, it's still too high. try flying it in manual mode. do short burst of full throttle without touching the cyclic, what happens? on board vids are the best way. you want that...

1000kv like the 8 and 9" props better on 4s. less wobble. There all calibrated right? did you flash them or is the firmware still bone stock?

hahaha. When i leave the boat, it aint actually safe till it's back. the shore is harder to get to than you can imagine. I've tried "walking out" when was stuck down in there before, i never got a hundred yards after hours of crawling, bending, etc. I'm pretty good with if i got to leave one...

for a quad, ezuhf is definately the ticket. it falls in, has a spectrum analyzer built in so if you do have problems, you can diagnose them without blowing another $300 on sniffers. the rmrc kit came with everything you need including antennas for $320 the quad wants the diversity rx. i...

heres the 1080p vid. raw footage. Seen a little here and there, but nothing as bad as mine has always been. 1080 is tough fpv cause you go through so many situations

I'm 6 months in FPV in quads, only fly when i goto the river and that's every 2-3 weeks, have burned 100's of thousands of mah FPV. so far all i've seen that sucks is you can't power it so it has to be kept charged. if it dies, so are you. It is easy to forget to shut it off and have it drain...