Search results

Japp i was reading this yesterday. I dont have the situation that my ESC get hot if the bird just stands and the lipo is connected. They do get hot after 8 to 9 min hover. I dont have anything to measure the temperature, but i can put my finger on without getting burned and i can keep it on...

Hi I am selling my MK spare parts. Following is in stock :) MK FC 2.1 ME - never used, but already pre assembled from RTF dealer Scope of delivery 1 SMD-preassembled board (acceleration sensor is mounted) 3 MEMS-Gyroskope (assembled) Other components: 1 Elko, 2 5V switching regulator...

Thanks Ken, had some time today to test some settings. All I can say is that this thing is so smooth in the air and so easy to fly i am more than impressed. I think i made my choice future builds that should be a vid platform will be WK-M. Boris

very strange one i already found it was the cable from the graupner receiver to the WK-M changed it it stopped, but strange anyways :) Boris

Its controlled by the DJI WK-M tried powering it from a BEC than directly from the WK-M. Strange one at the beginning everything worked fine than i moved the frame a little and this effect started ?

hooked up the AV 130 today and getting a lot of jitters especially when the motors spin up or down. Any recommendation how to get rid of this ? Tried to place servo cable as far away from any ESCs as possible. ? http://sprealinvest.at/jitters.mov

dave i am pretty sure they are the same ones i am using and can be seen in the pic from post #141 in this thread. He just has them the other way around. Boris

for me its fine, i don't think the force i put on with my hands is in any ways similar or as strong as the weight of the camera produces. But of coarse it would be better it would be stiffer. Never really had an issue with this. But one has to consider that i am only interested in a good...

Center rail bottom to bottom of landinggear about 27 - 27.5 cm. Again AV 200 from bottom of center rails to the big tooth wheel about 25 cm. If the cradle is in the highest position the tooth wheel if the lowest point on the AV 200. If the Cradle is mount lowest you will land on the cradle and...

here you can see the amount of play youhave forced with the hand. The standard battery contruction im my eyes adds to the stiffness of the two rails since it attaches them to each other. http://sprealinvest.at/play.mov

Hi Ellipz, AD 8, extended landing gear, AV200, just measured it approximately and also depending on which holes I mount the camera plate/cradle i get about 2.6 cm to the bottom. Here a short video with a 500 Eos and 10-22mm lens about 800 grams plus of equipment with no FC stabilization and...

this time hooked up to a power supply 5.8 v http://sprealinvest.at/burnbaby.mov only small red glow not enough to burn anymore :)

yeah yeah the BEC can only do 6V 3A I have the same one for the AV 200 working without any probs wonder if they check them before they send them out. Gonna do it on more time and put it on video :)

just hooked it up again its working and burning at the same time ? whats going one. they take 6V or did i miss something ?

strange one it cant be i twisted cables together to quickly check if its working, why would i put black and red together, (couldnt check later because i ripped everything off as fast as possible, as if that would safe something :). Have to check the BEC although I had different device running...

**** i just blew the servo from the AV 130, no clue what happened. Hooked it up the first time and smoke ? @ tahoelight. Japp taking of and putting back on is very important to me, after experiencing the AV 200 and how much care it needs after every third flight. Boris

took your advice and reinforced the vibrations mounts. Its a little bit of a vibration loop now. Although I dont think to much will be transfered. What is good is i can vary the amount of stress/hold i can but on the mount. More vibration mounts gel action is increased or stiffer if wobble...

Hi Cedric, thanks for the answer. I have them on my new hexa and cant decide which props i should use. Looking forward to your results. Boris :)

Hi Cedric, really looking forward to your test with the 2820/14 axis. Will they be next or are they just next on the sub menu on your page ? Thanks Boris

throttle control is very different. With my AD8 MK I would be loosing it to fly it in the apartment. A little over mid point and the thing would be against the ceiling. Flying seems a lot simpler with the WKM in attitude mode. I couldn't try it yet but I am wondering when the throttle really...