Search results

thanks guys will try some different firmwares but doubt it will take care of the problem, have a WKM not really in use at the moment, gonna try that also. Voris

Does one of you already have experience with the ECS32 with NAZA ? Have everything setup TBS Naza ESC32, ESC run with servo tester no problem, but i can't get them to start up with the NAZA. Melody comes but the set beep doesnt come and the LEDs on the ESCs keep on blinking red. Do I have to...

really looking forward to getting this in the air ! Also keen to find out what these ESC32 can do. TBS is certainly the better looking bird as the QAV500 :)

Sorry to hear that Meme. I investigated my QAV500 and plainly from the components i can't tell what caused the crash. Second test will be once i mount the components again either on the QAV or the TBS and lets see what happenes. Really don't like it if you don't know what the reason for the...

Hi Tim, lets me point out at the beginning that the crash has nothing to do with your frame or the vibration free or dirty zone etc. I really like your frame the layout, the amount of space to place components, the vibration dampening etc. Out of experience having down several WKM builds WKM...

Ah thanks didn't think of it that way. Just looked at some mounting of the antennas on some FPV planes and thought the way i had it now its the way to go. Thanks gonna try it your way !

Yes in this flight morning time wanted to take it easy and check out the place and tested the video range i was in attitude mode. It had a lot more oscillations in the flight when it came to full forward and throttle flight than it did on the other days. Think i am going to stick one of the WKM...

What you mean with bunny ears the Ezuhf antennas ? They are normally not side to side but somewhat 90 degrees to each other. Damn and all the dirt on the frame turns out to be cow **** :) Funny its only the arms thought that are bent like crazy none of the plates have a crack or are hurt in anyway.

hmm just lost my QAV500 :( strange one no more stick control and at a certain point a strange drift first left an then right to the ground. Only thing I did when i noticed its going for the ground was to cut throttle completely, hope the motors are okay. But will be fun to diagnose what...

I will get around to it the next days and i will let you know. There was a good explanation on this forum for the digital readings but I can't find it anymore. But you are right first value indicated signal strength second signal quality and than you have a 3 number indicating how many times...

hmm because it says in the manual: http://team-blacksheep.com/tbs-core-manual.pdf "The EzUHF is the first FPV UHF system that supports digital RSSI. To feed that information to the TBS CORE, connect your EzUHF receiver to the ImmersionRC Tools and select a channel on the “RSSI Needle” setting...

Kloner got the TBS frame finally yesterday. How did you connect the Immersion EZuhf RSSI connection to the TBS Core ? Did you use the two small pads on the frame RSSI and GND or did you connect it directly to the TBS Core. Doesn't the digital RSSI feed from the EZuhf which doesnt need additional...

kloner whats the weight of these, couldn't find anything on the webpage thanks Boris

nice meme, zero vibs to be seen ! What props do you have on ? 10 x 5 graupner ?

Did you calibrate all your ESCs. That a way to get rid of it if you haven't done it yet. I have the same issue though with two of my quads even thought the escs are calibrated. But i guess since you have the f450 you got DJI ESCs. As far as i remember they can't be calibrated. In general don't...

very nice mombasa ! you were maneuvering some tight spots there ! Boris

no opposite in must cases 4s over 3s will give you more flight time. The props don't spin faster at normal hover. You have a certain amount of thrust you have to generate to lift the bird and that will be the same as long as the payload is the same, not matter 3s or 4s. So the RPM stays the...

really wait with the decision making once you mounted your camera. The game really starts once you look at the first footage you made. Than you will start looking for ways to get the smoothest flight. Testing 3s 4s different gains, props. Than the nest round starts what best in wind for good...

From my experience testing with 4s 5s 6s on Octos, the more voltage the lower i had to but the gains to get a steady flying bird. You will notice a difference when you have a camera mounted. You are not noticing any flight time difference between 3s and 4s ? strange one Boris

cool that you found it right away ! Is normally always these steps. First clear up what the expectations are how fast and were the lock should happen. There are people who get nervous if they don't get a lock in their apartment house etc. Second rearrange components etc. Boris