Search results

theortetically you can. As far as i understood the zenmuse can be powered up to 12s. I would double check though with support or the manual since the WKM powered from one source and the zenmuse powered from a second source are connected via Can-bus that share a common ground, but they probably...

DAX the question is what camera you are deciding on using ? CS 3 Axis will be a great product but it will not touch the grounds of the zenmuse when it comes to giving stable footage and smoothing out the copter movements in wind etc. Zenmuse on the other side for now will only let you use a...

throwing in some additional stuff ! 11000 4s maxamps lipo. maybe used max 7 charges probably less ! and the two never used freely servos Total package price new: Cinestarframe Kit: 1749,00 CS 2 Axis Gimabl: 960,00 CS Anti-vibration Adapter: 159,00 8 X QC...

HI Guys, I am having less and less time and space for my hobby so one of my bigger frames has to go. Picked the CS since its taking up the most space and I am happy with the GH2 as my primary camera so my S800 is enough for the job. Build thread...

Found it interesting one. On the VTX there is a fan for cooling if I desolder it so fan off the gimbals behaves normally. Think the whole vtx just draws too much Boris

hmm the cam is not even on ? But will check that !

Different problem now. When i connect the videos transmitter to the video output from the zen IMU the Zenmuse will not boot up corrrectly ? Check the video : https://vimeo.com/48104916

oky since 5.10 wkm fw ppm is implemted, new firmware came out today hmmm :) no trying it :)

gonna check the release notes. I think the problems were always in combo with traditional reciever approach the s-bus users didn't suffer

hmm didn't they release ppm for the WKM but not for the gaza yet ? confused

Wire for every channel separately like a traditional receiver, thus no one wire ppm or s-bus. Boris

okay the red Led indicated that the cameras is not on :) and the slight yaw drift stops once in the field i was told by z15 nex owners lets see. All in all i am really happy to finally have the zenmuse ! Boris

Hi Guys, finally got my Z15 GH2 and I have one or two questions. Want to use it first as a single person setup, and not even control it in any kind of way. Thus i hooked it up didn't connect any RX and its behaving strangely on startup. Pan is drifting more right after startup and a little...

Look closely at the LEDs you will see a difference between the green and the red LEDs. I think to remember that the red ones have a very small red dot in the LED that can be seen ! Boris

hmm it can actually only be a couple things, if i compare the TBS being fine at full throttle compared to the QAV500. 1. ESC are different, flashed vs DJI stock 2. Motors are different , axi vs. Tiger 3. Frame configuration is different, but qav500 should actually have netter flight...

hmmm i have some tiger motors on my qav500 http://quadcopters.co.uk/torxpower-2216-pro-short-shaft-brushless-motor-900kv-330-p.asp and axis 2217 on the TBS, they are not really different from each other think 30 Kv difference. Lets see. Think Ken bought these pan cake motors that tim has in his...

Hi Elliott, i have the same issue with this setup : Its a QAV500 with Naza and DJI ESCs, tried all different gains no chance to get rid of it. I also have a TBS ESC32 Naza setup and I don't get the vibs at full speed. I suspect the ESCs on QAV500 DJI ESC are the problem so i switched to...

Just set four of them up for a FPV quad. Its not hard but time consuming. Hardware steps: Soldering main power lead Elkos UART/FDTI 6 pins connector Heatsink for the Fets, additional you could add in the drivers. PWM conncetionhe Heatshrink. Firmware side. They come flashed with FW...

got it- I set the minimum PWM value to 900 now they work Boris

Also noticed the laziness of the axis starting up on my TBS, gonna change the voltage thanks ! Boris