Search results

Kloner recommends the latest version, 5.26, so you do not agree. From what I read 5.24 has the same issues, many are reverting back to older versions than 5.24

I was advised by Kloner whom I respect a lot not to downgrade to older firmware because many needed features will not work, isod, waypoints, etc. If the new PMU does not do the trick I am moving on to another FC, perhaps A2 but then who is to say there won't be problems with it? Super X is...

I see it has been a months since anyone replied to this thread as well as the other one addressing this issue. I I have been having problems with my wkm IMU V1, GPS V2 on and off for months now. Sometimes I would start up, take off and she would be in attitude, then gps would kick in after a...

I see it has been a few months since anyone replied to this thread. I have been having similar issues, have you resolved yours? Perhaps you have engaged in another thread, if so can re redirect me? Here is my issue: My Wookong was on a hexacopter that crashed but sustained little damage. It...

Pretty sure my antenna puck is bad. Anyone have a used one for sale? thanks John

An excellent design, proven over and over again Andrew, That's a great explanation of the design philosophy behind your product. I am one of those who will testify to the durability of these frames, I own three of them now. Two have met devastating crashes and it was only the landing gear...

Thanks onlocation (I once had a boat named that, enabled me to have a great answering machine message, " Sorry, we are not in the studio right now, we are on location...") Anyway, it still will not work, there is not enough room for the plug, I need a right angle plug for my Sony Nex7 to fit...

Motors have been starting up OK most of the time. I wanted to alert everyone to a great dealer. I bought my T-Motors from Christos in Greece. http://www.multicopter.gr/ Not only did I get a great price he always replies very quickly to any enquiries. Most recently I had one motor acting funny...

I just installed V2 and I kept getting the same message. I calibrated 3 or 4 times and still the same issue. I kept bringing it outside and eventually it started to fly. I then kept getting an issue with voltage protection, kept landing itself even with full batteries, I turned the voltage...

I just installed the Naza V2 on the Hexacrafter 650. First I kept getting error message 27 that I needed to do advanced calibration of the IMU and no matter how many times I did it it still kept saying I need to do it. I did many times and kept recycling the power and finally I got the copter...

The hypercable is mini to regular HDMI, so I guess an adapter has to be used, plus the website says ships in 4-6 weeks! What!?! Why would anyone wait 6 weeks to ship out a cable? I don't get it.

Stripping the plastic coating, brilliant! Unless someone advises against it. I'll look at the hyper wire too, maybe that is the better route since the one that comes with the Freefly converter is a little short. Thanks

So I have my brushless Gimbal fine tuned and working pretty good, it's a Hexacrafter http://www.hexacrafter.com/index.php?id_product=73&controller=product with Alexmos board and IFlight 4008 motors. The problem I am having is I have my FPV set up with HDMI out from the Nex7 to Freefly's HDMNI...

To improve on vibration reduction I did some modifications to the HC800. I had some good results by using a material called Sorbothane in my F550 build so I thought I'd incorporate it into this build.I started by cutting down some aluminum plating I had to these rectangular shapes: Drilled...

WOW, Costa Rica, how cool is that. You will have so many great filming opportunities in that country. A little boring here in flat Florida. As to your problem you might want to check the stability of your boom arms. I had one motor giving me some problems and then when I carried the craft I...

I hooked up the snake to all the ESCs and the other lead to the throttle input on the RX to just run the motors and nothing happens. I must have done the snake wrong and I am getting no signal to the motors this way. That means I did not calibrate the ESCs initially but my interpretation of...

I calibrated them with a snake I made so all the ESCs can be calibrated at the same time. However I am not sure what signals I am supposed to get if calibration is successful. I am using a Spektrum DX8.I am learning from others that on larger props this happens occasionally and does not effect...

Setup: 3520 T-Motors Maytech 65 A Simon Flashed Opto ESCs 15x5 Xoar props Latest WKM firmware flashed Idle Speed set to max Here is what happens every 4-5 times I start up: http://www.youtube.com/watch?v=UBE8Ytv6_K8 Fast forward to about 1:17 to see #1 motor not starting Anyone having this...

AUW is 696 g, I flashed WKM with the latest firmware about a week ago. Maybe I should check the DJI threads to see if maybe it is a firmware issue I have 14x6 props too and I had them on for about a week and this issue did not come up. I just switched to the 15s because I was advised in calm...

Here is some more information.. first of all I have been noting the wrong motor, it is not #6 but #1 in the video. I know why I was mistaking it because in subsequent tests it was doing it with motor 1. I just did further tests and after about 50 start ups other motors did not spin up at all...