Search results

FINALLY, after months of farting about the droidworx Y6 took to the sky (low hover) this evening. Started out as a MK upgrade but is now (and finally) a wkm build (with HW 30A sec's, the smaller of the two Torxpower motors and graupner 10" props) Initial teething problems were, as they are in...

Not sure if anyone will happen to have these, but: I'm looking for 3 droidworx heavy duty (50mm) coaxial mounts. ie: enough for a Y6 build. Thanks

More up for grabs… 6 x Roxxy 2827-35 motors 6 x 3mm prop mounts 6 x 5mm prop mounts MK props - at least 6 propellors - 6 shown in the pic, but i know i have a bunch more which will be included. £180 including UK postage (additional overseas postage cost depending on destination) ---

Just thought i'd post a couple of pics of my Naza FPV build. The ImmersionRC kit is really good to work with, all required cables supplied and keyed, plug it all together and i just works and ezOSD is very clear. The FPV parts are sandwiched out of harm's way with a second flamewheel plate...

what are people's opinions on when it's too windy to fly? it's forever blowing at a strength I think is unsafe to fly in, but just wondering if I'm being too cautious. I used bought a turnigy anemometer and the steady wind today is 12-13km/h with gusts at 25-34km/h

I've had a long think about my multi-rotor collection and decided to sell my Mikrokopter electronics. The honest truth is i'm scared sh!tless that i'll have a silly stack and trash the lot, which means i'm not flying it, which is therefore a waste. The flight electronics had a few flights in...

had chance to fly a few packs with both the wkm and naza today. first tentative fpv flight with the naza was ok, but not the best location. i do however keep experiencing niggles which spoil it all. naza, as the flight progresses, the throttle becomes less and less responsive - still plenty...

Could anyone advise on how to set-up an appropriate failsafe setting for the DX8 with both the WKM and Naza units please?

after the issues with two motors spinning differently to the others i thought i'd swap in four 40a rctimer ecs's. spent a yonk sorting it all out. esc's card programmed and calibrate with the tx. tx recalibrated in the wkm app. did a 'waggle' test by hand to check. nightmare. firstly when...

too blinkin blowey here to attempt a flight outside, but had a crafty spin up in the dining room anyway. has anyone else noticed the following. when i arm the motors and they idle, motors 2 and 4 seem to spin significantly slower than motors 1 and 3. as i increase throttle they are still...

doing a Naza build with 4 x 30a hobbywing, flyfun esc's. could anyone educate me with approprite settings, using the programming card. i'm guessing: brake - off lipo cut-off - low start mode - normal timing - high governor - off has some 'funky' experiences with the flashed...

is it possible to use a 6 channel Rx with a naza? using channel, 5 or 6 for flight modes rather than ch7?

success! just had a first very quick flight with my wkm/flamewheel build. when i first opened up the boxes, i thought a wkm in a flame wheel would be a crammed mess, but with a bit of thought it all fits 'mid deck' neatly, leaving a space at the front for a GoPro and room on the top for the...

i'm having issues with my wkm build and wonder whether anyone can help? set-up wkm/flamewheel 4x turnigy plush 18a reflashed 4x 3506/25 650kv motors 3cell zippy lipo DX8 radio, AR8000 rx escs do work, tested with rx and motor. i've assembled everything, double, double checked...

I have a couple of sets of motors up for grabs - ideal for a knock about/diy project. 4 x turnigy motors, with longer wires and 2mm bullets soldered and heat shrinked. The shafts have been cut short from the bottom. £44 inc postage within the UK 6 x keda motors, 4 with 3mm bullets, 2...

just wonder whether anyone can explain why my motors click intermittently and is it an issue to be concerned about? initially i though it was cheapo motors, but having swapped in some t-motors, the clicking is still there. this is happening on my arducopter quad, esc's are turnigy plush 18A

Just wondered whether anyone has any thoughts/experience on this one. I've been flying both my hexa and my arducopter quad on 10" props. The arducopter, which has seen most action recently, seems to require more than half throttle to get it off the ground (it's a pretty light build) and keep...

Bit the bullet and bought a netbook to run MKtool, Arducopter Mission Planner etc. I'm a mac man through-n-through, have been for 25 years, but running MKTool and Mission Planner through Parallels has been an effing slow and tortuous process. On the upside the cheap and cheerful dual core...

I'm about to have some test parts cut from 2mm carbon fibre and wonder whether there'd be any interest in these from other Droidworx frame owners. The parts will include: • standard size lower leg plates • low profile lower leg plate - not suitable for use with an underslung camera • a variety...

This relates to my recently finished DW Y6 - running robbe roxxy 2827/35 motors. Not test flown her yet. Should i go for Graupner elektro 10" x 5's or 11" x 5's ? What difference would i expect to see between the two? Thanks, David