Search results

I just ordered one. As Part of my SFOC requirements here in Canada I need to keep an accurate log of all flights, locations, duration etc. I'm hoping this little tool will make keeping these records a breeze. SIM card cost is $10 a month and it will effectively share data with my smart...

Am I correct in assuming k1-k3 are the basics gains and k4-k6 are the altitude gains? Manual doesn't say. Should I asign 1-3 to a dial? I have k1-3 set at 150% and k4-6 @ 110% for my maiden. When I do assign them I see the channel is functioning in the mixer but the set gain values don't...

So I just installed the a2. On power up I get a sequence of led colors. Green red blue purple yellow green. Then led light goes out. My motors go thru the chime sequence. 6 beeps then a multi beep. Like normal. Then # 5 and 6 continue to make a beep that continues. I cannot connect to...

Looking for someone that really knows their stuff to help me with setup for my maiden. I'm just lacking confidence. I could travel a couple hours. I am happy to pay someone for peace of mind. I would want my futaba 14sg programmed and a2 configured. Thx.

I do have a 7008sb reciever but I'm thinking I will use the built in reciever as this eliminates a connection and an additional failure point. The down side is I cannot use voltage telemetry to my 14sg. What are you guys using and why? Pros and cons? Thanks.

Here is a build log for my new hex. I will start off by saying the frame from Andrew @ Hexacrafter is top notch just like his service. The arms are basically hockey stick shaped CF tubes. The main plates including the esc mounting plate and motor mounts are all 3mm glossy cf. Everything...

$2000 pre order price. $2200 regular.

Used 2 flights. Upgrading to 75amp. Both servo wires and power wires have been extended. I have also added shrink wrap over the entire esc because I didn't like how the capacitors were not supported. I did this after speaking to Patrick and he agrees it's a smart idea. $40 each. Usd...

I've heard from a few people this is a rebadged A2 IMU. Is that correct? Has anyone tried it with an A2?

I Was bored last night. Set up a test bench with my kde 4215-465 and 55a esc's. Using 16" props the amp draw @ full throttle was close to what KDE has in their technical data. They say 39.7 amps. 45.7 amps peak was what I got. The motors were cool. 80F max. Using 18" props the results...

Gryphon 1000mm hex wookong with v2 imu (a2 imu) 2 x 6s12000 Do gains look ok? I think it will be less jittery when i have the weight of the gimbal and camera bring the COG lower but I am open to suggestion on how to dial in gains. Oh, and do you like the Canadian Heli Pad? lol Thanks

What's your go-to lens for aerials? Maybe you have a couple preferred lenses. Please share any experience with this camera as well if you like. Thanks.

This will be long guys. Please bare with me. Timeline: November 29/2014. Ordered superx standard and osd from Xaircraft America. Never heard from XAA again and had to file a claim with visa. Recieved credit from visa December 22. December 17/2014. Ordered superx standard and osd from...

Ya, I know guys. Totally unrelated to multies but linked to them somewhat. I have a gmc acadia with a 32" tv for the kids. It is running off a xantrex 600 watt inverter. (Very clean power btw). My main battery is a 880 cca agm battery. When I start the truck the inverter input drops...

Just wondering of it's worth it as an extra layer of protection to take all my servo pin connectors out and soldering them on the crimp connection. Do you do it?

Overall I am happy with the lens but like most things in life there are trade offs. Here is a good example of the biggest issue with switching out the stock lens.

I have 3 pretty beefy all metal servoless retracts going on my gryphon hex. I have no A couple guys online said this particular type are garbage and fail all the time. I've talked to another guy that said he used a capacitor on the rx and he's never had a problem. I have no idea of amp draw...

The little brother to the H14. 6 pound capacity I assume. In the $2000 price range. It will be a front runner for my hex for sure. Btw, the h14 is available in a multirotor only version now for $3000. I think this company is gonna do well and take some market share away from the...

I placed an order on Thursday night from HK China. Paid extra for DHL but was still super impressed when the DHL guy rolled up here in Toronto Canada. Too bad the order I just paid brokerage and duty on is for some poor guy in the United Kingdom. doh! :mad:

They stopped a couple weeks ago. Is this a site wide problem or specific to me? Thanks