Search results

Anyone looking to order the Phantom 3 PM me, I have a discount code for 5%.

What are you running when it comes to Low Battery Level and Critical Battery Level for the Phantom 2 smart battery? Mine is stock 30% and 15%. After 23 minutes of flight and landed with the critical warning I was at 15% and battery capacity was at 780mah which is about 85% of the total battery...

I was out today with my X650-Pro and was into my first fight of the day. All started off well until the end where the copter came crashing down. At around 14.3V I decided to bring the copter in, flipped RTH and watched as the copter made its way back without any issues. As it started to...

Can anyone tell me where to download the English version of the 2.4G Bluetooth Datalink Assistant software? Went to DJI site under the support tab and downloaded the software but its the Chinese version.

I'm trying to download the DJI WKM Assistant 2.04 software from their site, but when I try to unzip the file its says the its not valid. Can someone provide another link for me to download the software?

I have a WooKong-M with a version 2 GPS (all white and grey connector) how can I tell if this GPS needs the firmware upgrade to avoid the FOD?

I was out flying today in NJ and noticed that getting anything above 5 SAT's was very difficult. I was wondering if anyone else in the area was seeing the same issue. I have been reading on the DJI thread that the GPS constellation is not in the best of health these days, and to check for solar...

I have the x650 Pro (stock) with tarrot gimbal and Hero 3 attached, When I enter GPS mode the craft is all over the place this includes all axis of movement. I have my gains at 1.0 for everything. I have included the link to the log file. Any help would be appreciated...

I'm having a brain meltdown on something that should be easy but I'm going around in circles. I'm trying to wire up 2 camera's to a 3 cam switcher and the XA OSD. Can someone take a look at the attached picture and let me know if this looks correct? Thanks for the help everyone.

I just wanted to share my thoughts on the XAircraft America and the SuperX. First let me start by saying that I have multiple DJI WKM flight controllers as well as various DJI frames including the S800, F450 and F550. Needless to say I have many thousands of dollars in DJI equipment. After the...

What are the suggested battery configurations for the 650 Pro? Anyone running parallel 5800Mah setups? I'm looking for the longest flight time possible with a stock 650 Pro.

I took my 800 up today to test my FPV and iOSD components in preparation for GCS control. The flight was going well in ATTI and GPS mode, I decided to test the RTH switch to see if it would function. When I activated RTH the S800 turned and took off at a steep angle (almost flipped upside down)...

Does anyone know if the DJI waypoint hards uses SMA or RP-SMA connector? The manual says SMA but I know when dealing with say a Foxtech hardware I need to use a RP-SMA antenna and was wondering if its the same with DJI.

What are your gain settings for 5.16 firmware Just finished building my S800 and loaded the 5.16 firmware to the WKM. I was wondering what gain settings I should start with? My setup is stock S800 with a battery weight of 1,696g (3.7lbs). Any recommendation on what first level and second...

I was wondering if anyone has any experience with covering the pressure hole with cotton or breathable foam to help with wind turbulence between the frames. I know the open source APM guys cover their sensor to help with the turbulence from the rotors.

I know the S800 requires 6S batteries, can I run 2 3S batteries in parallel?

I was wondering if there is any way to check the vibration levels that are seen by the IMU? I know some of the other "hobby" FC have this capability and would hope something as expensive as the WKM would expose the same capability. Thanks.

Just wanted to get recommendations on using zeal tape or some other damping tape to secure the WKM to the S800 to reduce vibrations.

I have an original WKM before DJI started shipping them with the PMU. I just picked up the RCTimer M800 (S800 clone) and have read about an issue with the "old" WKM cutting power to certain motors. I want to know if I should reach out to Rober from UAV Products to have DJI replace the unit since...

Does anyone have a link to Assistant Software that supports firmware 5.16? I'm going mad trying to find this version. DJI website only goes back to 5.20.