Search results

CineStar 6 with a history of multiple crashes for sale. Any reasonable offer will be considered - 843-637-0455

Looking for 1 Freefly F360 0866 servo

Thank you so much for your reply!! Dixon

I've tried it in the assistant and failsafe does not show up with the Futaba.

I have a Cinestar 6 with the DJI A2. Does the A2 assistant still show failsafe when I shut down the Futaba Tx?

I have 8 batteries but they are all the same. I have the HItec multi-charger X4 AC plus, not sure if it has the ability to check IR.

My all up weight is 11.5lbs but I have just been working with 8.4lbs while testing the new motor and esc combination. The 2 batteries I have used running these test have both ran hot at this reduced weight. With the old esc's and motors and at full weight of 11.5lbs the batteries were just warm...

Good information, I am not the best at maintaining storage levels for the batteries but they are kept in a storage room that runs about 78-80 degrees and never exposed to sunlight. I not sure if it's a storage problem or a mechanical problem. The fact that they started acting up just after the...

I am using 14 4.5 APC's and lifting 8.4 lbs I also used Tarrot carbon 1455 props lifting the same weight. The batteries heated up with both sets of props

I am flying with the Zippy 30c 5s 8000mah battery. As of late I have replaced both esc's and motors on my Cinstar 6. The motors I have now are Sunnysky's-4010/kv450 and the esc's are Range Video 60a. This combination seems to cause the batteries to run hot to the touch and also get puffy. The...

I have adjusted the gains to resolve the looping, not much success, I have tuned the WKM several time with no success and realigned the motors several time but still no success. I changed out the APC 14x4.8 to APC 14x5.5 prop and there was really no difference in drift. I didn't think of...

Thanks Andrew for clearing that up for me. The props that I am currently using are APC 14x5.5 form Quadrocopter. Prior to that I was using APC 14x4.8 Slo Fly. Another issue I am having is when I yaw right 90 degrees, the Cinestar will drift back to the left for about 8 to 10ft at 45 degree...

Calibration for TX max & min throttle during build? I purchased a Cinestar 6 with a Wookong flight control system along with six Maytech 45a opto esc's. Unfortunately, the person who built the machine did a very poor job because I have had nothing but problems from the very start. Fortunately...

I am looking for some that are a little less expensive. Graupner has a set of 14.8 that are in my range or some 14.47 carbon from Helipal.com

I currently have APC 14 x 4.7 SF. I have read in the forum that the Slow fly props are not that compatible with the WookongM system - causes quite a bit of the jitters. In the same thread they suggested the Graupner 11x5 prop. According to the spec page for the motors I have the suggested prop...

Good to hear about the white flashes not being dangerous! I took the hexa out again late this afternoon after messing with the gps mount again and apparently it helped quite a bit. The drift is now maybe 2 feet. About the magnetic declination, what is that and how do I avoid it as far as the...

Since posting this I have recalibrated the compass, reestablished the cog, balanced the props, recalibrated the gps mounting and increased the gain in the yaw from 160 to 200. I still have the yaw problem when I rotate right or left. Any thoughts? Thanks

I have a Cinestar 6 with Wookong M flight control. When I yaw to the right the copter rotates fine but upon completion it seems to float backwards about 10 - 12 feet. Then as it is regaining its position moving forward the LED blinks 3 white blips 3 times. I understand this to be a signal for...

Ditto!

I found the problem, the aileron trim on the transmitter was set to the extreme left. My cat will do anything for attention.