Search results

Hi An old thread brought to life :) After watching the Cinestar 3 Axis Gimbal Tutorial and comparing it with the pan assembly I have, there seems to be difference in the two. In the pan wheel that is. As a result, I see no need in installing the supplied four metal spacers as the outer four...

Tried the Skyline with 1.7b today. Some notes on tuning: - Did the manual Center Tune thing with gains at 0 for all axis with servos detached from tilt belt and roll/pan teeth. Transmitter was on and all the trims and sub trims were at 0 naturally. Sticks centered. Tuned until rotation stopped...

I think so too. Flew three flights today. The roll was way off on every flight. On one flight I landed and booted Skyline. No help. Another problem is the very rapid movements of tilt and pan. I have maximum minus expo on the transmitter but the movements are nevertheless very rough. Anyone has...

Yes, unfortunately so. Took the USB off, turned Skyline off and on again. Not just once, but three times. Same result every time. Horizon not in level. Also tried to set just xy levels and booted. No help there either.

Did like above. The horizon is still after making xy-z-autotune calibration maybe ten times way off :upset: Brendon and co. NEED THE MANUAL!!!

Well now I badly need tuning advice: Put the center tunes in I have tested without gains so that the servos have stopped rolling and after that the gimbal went haywire. Did the set xyz and auto tune. Center tune values are completely different with auto tune. Position of the gimbal is better...

Well Fabietto it did! Grazie mile Skyline guru :tennis:

I downloaded and installed 1.7b and uninstalled 1.2.2 software. Now when I try to connect my USB programmer to pan input, I get the result "failed to connect to Skyline". Port is same as before, COM10. Uninstalled Silabs usb driver and re-installed it. Made sure they are the newest. The same...

I have the newest FW from PH site 1.2.2. I have the pan servo connected directly to the receiver. Today I connected the pan servo to Skyline´s pan servo connection and the pan input wire into the receiver. The Skyline did not boot OK. It went to red and did not move at all. Is this because FW...

A friend of mine milled me these very nice carbon-fiber mounting plates for the top plate of my Cinestar. I am planning to mount all the Wookong-M components on the plates. A question: Is it advisable to use the M3 rubber vibration dampeners to mount the IMU? I am going to place the IMU under...

Actually I will go with a standard 8 at least in the beginning. Sorry, the title is a bit misleading. Tried to edit it but no go.

The frame arrived and I managed to get it built. Quality and instructions were up to the price, i.e. very good. To mount the Power hungry board I needed some plastic standoffs, screws and bolts I had left from my Mikrokopter/Droidworx AD-6 build. The power board came with a few standoffs but...

Yes, great footage indeed! Can you kindly share camera and gain setting details fabietto?

Hi Is someone flying Mikrokopter with FRrSky TFRSP receiver? If yes, how do you setup your failsafe? TFRSP has its own settable failsafe, Mikrokopter its own and my Futaba T10C its own. I havent set the failsafe yet, but it would seem logical that I should 1. disable the transmitter failsafe...

Pan system: I zeroed all gains and did the pan center tune without the gimbal attached to the copter and found the center tune i.e. the servo stopped rotating. Saved it. After that I adjusted pan position gain to 100 and pan velocity gain to 60. Attached pan input and pan servo cables to...

About tuning: Xyz axle calibration works OK but when I auto tune, it never finishes. Should it finish at all? AV130 360 kit and Skyline RSGS v. 1.2. Thanks on the gains tips. Will try them and tell how they work.