Search results

what i'd do is go add two gopros to this thing and hovr it in manual and see where the stick is riding, is that about 7 oz of camera? Bring that back with what prop and battery it was and i can answer the size part better. A total weight would help too

mines doing that too with the update dialog try this, go into the radios endpoints and make the first 4,,,,,, ele,ail so on and make those 125 and try assistant tx cali again. it sounds like the endpoints aren't far enough, that would make the csr or whatever it's called not get tickled enough...

atta boy, it's a common smart question. the big money gets axi,,, 2217 , my money uses suppo 2810 2814, theres rc tiger, theres avroto, there are alot of options and is a good time to sort out if your gonna carry more weight later or if it's not propped right now, you can add 100kv, take away...

hey, anybody that can fly under goggles is alright by me hahaha,,,, you were too far away. if you did cause it, it was good practice for her to keep her attention where it should be cause that bike aint no joke

i've seen alot of dji motors not work, dealers replacing them on here, but usually its where the motor doesn't start at all, prop goes back and forth real slow. show your dealer this...... whod you get it from? this is way not what suppose to happen, it'll crash sooner or later. suprised the...

awesome....... that motorcycle guy threw it down didn't he. was that a dog going at him after? Are you flying on 2.4 radio?

nice! want to trade some stickers for a embroidered shirt? Sounds like shes ready. if you have uhf, hook up the rssi, super easy and super important info. Lets you know if it's all workin right. the design makes that a much more likely chance but you never know. keep after it, we want to see...

this is a post here, has all the info for updating if you want to http://www.multirotorforums.com/showthread.php?5814-FLASHING-E.S.Cs.

looks like a rear right motor then right side in the later part of the film, was the motors rotated at one point these guys are right, looks like a bullet connector on the esc or the wires inside the motor. the motor wire bullets can be resoldered, get some heatshrink so you can cover em back...

that you quoted above was from the ama website at the link quoted in it under july 30. This is alot like medical marijuana laws in that until there is a law saying you can, you can't do it. people in that industry just want an actual law to follow but they haven't been able to do that for 14...

OK, the easiest way out of this is to calibrate your esc's. Take off all props, take each esc servo wire off, put it on the rc receiver throttle port, put your throttle to full and boot up the quad, it should beep different after a few seconds then you drop the throttle. It is instructions that...

http://www.rcgroups.com/forums/showthread.php?t=1513678

yea, that's what we do here. www.waterfowldecals.com that's awesome! Did you catch it on tape? everything work like you thought? get it on camera?

what radio is in it? kinda sounds like it's hitting failsafe as in loss of reception. usually when a connector or esc acts up, the motor stops, falls like a brick. I'd look at range testing your radio. read the manual about how to enter that mode, makes the antenna off the tx really low...

on the calibration you'd want to do the mid stick throttle save. in assistant is everything moving normaly? your positive theres no rate modes set? do the green/black bars go all the way side to side in tx cali? why so many flashing reds, will it lock in anymore and go flashing green only...

I missed the mailman saturday and got "the card" so i'll go grab it tomorrow. sure i'll have a few questions. thanks again for all the links and advice. i was totaly lost looking at them. like the first multirotor purchase

I've been thinking about what all i changed to make mine going away and the props was what did it, but more, i was always running slo fly props when it did it, apc 10x4.7.....I think the big ear makes the yaw control work harder and heats em up. i tried changing motors, tried different apc...

you want v1.8 http://download.dji-innovations.com/downloads/naza/NAZA_Installer_1.8.zip for real? one wire from the futaba reciever to x2,,,,theres only one x2 and only one port on the receiver marked sbus, no way to mess it up. that sends the radio signals into naza, only wire you need on the...

ear plugs under the cam works great, there is no post anything to fix jello if that's what ya got. I gotta look this over again. love flying, but academics has always been my weak point..... writtting a story, haha, never made it of 9th grade.... I'm an artist, not a writtter does this close...

your receiver says sbus, plug one servo wire into it,,,,,, on your naza, plug that wire into x2 your naza should have three wires plugged into the back, the 4 pin one goes on led, the other wire from the vu goes onto x3 and all those wires should be pointed towards the back. I keep asking and...