Search results

that is exactly your problem. you might even consider re-soldering the bullet onto the wire just in case it's the solder joint.... you can also pry out the little prongs that make tension inside the connector, sometimes they get weak and don't hold a connection if it continues, look at...

i'm not sure, but that's what i'm curious for. I got a green lit one and a red lit one. Red lit one has the light on the barometer problem

were all doing fine so far. do me a favor, when you boot up your naza to fly, what color is the light inside the naza on top center?

how many red blinks? is it the gps blinking like loss of signal?

we kinda replied at the other thread. no gps right? if it is sagging like tstrike said under power then not when hover, your batt are saggining into lower voltage than you expect. Could be the prop changes drop 14.8 to 14.6 and land early, don't wait for it to tell you too

got a gps?

send a message to him Atti drops the power output alot, it looks like the left rear motor shuts off. try this, take the props off, fire it up in your hand and see what it does in atti. if normal. if you feel safe, fire it up in atti with props and rev it till light and see what it does, don't...

i barely made it into high school little lone out, books werent for me but i have this weird way of looking at stuff like from an engineering or physics standpoint. Like a mad scientist. I probably wouldn't have thought it through to match markings on props to decide which way they went. I look...

OMG.... whod you get it from?

got anything grindy? bench grinder, sander, hell file?. there not super hard, stainless not like that black hardened metal like a black bolt when you get everything if you need anything, i'm here if you cover shipping for whatever. ultra cheap

hahaha wtf we'll get ya flyin, i ask so many questions your bound to stumble on it sooner or later......

everytime or just every now and then? sounds like bullett connector, motor wire, something between the esc and motor not holding a connection do you leave the ground in atti?

take us a picture from the top all installed. when you start the motors, do they spin so air goes down? writing on top?you gotta look at it, but you can make which way it's going by how it spins..... you gotta look at each one, start em, let em stop, that way you see the spin.

that was a quad....... i'm not sure on the hex...... i always forget theres other than 4 motors If you look at assistant and your motors spin right, the props spin so air goes down

if you stand behind the craft and look forward, it is the fornt left and rear right that get the L....... when your still at the back, the prop blades on your side of the motor outermost blade spins in towards itself, if you spin it around, the outermost props spin towards themselves look at...

one other thing, t-strike reminded me of while i'm sitting here setting up a set of these motors. The shafts on mine are ground down just a tad, .15-.2" so that prop adapter sits on top of the bell flush and tight. they also have flat spots ground in em for those set screws to sit in. Makes it...

when somebody wants aerial fishing footage at sea for an nbc or affiliated company, does a 5n take that kinda footage? I picture it being used for intros of boats leaving a harbor or flybys of rods bent along a boat. it's used for little cuts right? I watch alot of this stuff on TV, we've...

this is that solder station thing i called free hands or whatever. This is how you make it easy http://www.amainhobbies.com/product_info.php/cPath/89_142_2013/products_id/235687/n/RCPROPLUS-Soldering-Station?utm_source=9_13_2012_newsletter&utm_medium=email&utm_content=RCPROPLUS-Solder-Station...

not cause it's higher powered but because it's on the 433mhz frequency also known as 70cm. it's a popular channel for things like garage door openers, alarm sensors and alot of weird things. Alot of those things don't work when your on around them. Guys talking on it with ham radios get pissed...

ouch,,,,,, touche