Search results

  1. kloner

    Battery & iCharger 306b related questions

    I write it on the side of the packs with a date. I pretty much ignore it till i have an incident where a pack was knowingly over discharged then i'll recheck it. I'm not gonna say a number is the end of the pack, but i've noticed a 4s pack will go from 20 to 50 in one over discharge and it never...
  2. kloner

    Servo wire mesh source

    http://www.cableorganizer.com/wire-management/
  3. kloner

    Undesired Wiggle

    sorry, looking at that video made me set my mind what i was watching from Take your props off and fire it up. feel around for vibes and recheck the prop balance,,, fix anything not totaly smooth. Somethings not letting a motor spin right. if you have a hero, place it on the ground looking up...
  4. kloner

    Battery & iCharger 306b related questions

    heat isn't a real problem with charging at higher rates, it's the chemical breakdown of the polymer in there that goes away. theres this plastic looking stuff sandwiched in with foil plates, lots of em. they have alot of new theory and rules to use em. If you abuse a pack too much to where the...
  5. kloner

    Undesired Wiggle

    welcome to a cs8 on wookong. looks like some outta balance motor/props and the cs8 with wookong kinda does that in the slightest breeze even perfect. add a bunch of weight helps kopterworx has these things carry a butt load of weight in an x4 config that appears to work, but with 25 lbs and...
  6. kloner

    Kloner, your Suppo motors

    thats just the one built into the tbs core.... more than enough for multirotors
  7. kloner

    SteadiDrone QU4D - Foldable GoPro 3 Quadcopter!

    you did a great job on marketing in the video....... i'd be scared to sell something like that with apm...robust but not the most reliable controller is it? I've seen it go both ways with the 3dr version Your drivers seat is on the wrong side......
  8. kloner

    Kloner, your Suppo motors

    I've tried everything readymaderc sells and landed on lawmate 2.4 1000mw video transmitters with securitycam2000 seawolf pixem cameras and i used ImmersionRC EzUHF that knocks my rc signal down to 433 and opens up that 2.4 for video. the newest firmware has made all immersion receivers, ever...
  9. kloner

    FPV Air to Air at the Shop

    that had some weird clips to it good luck in your venture, hope it all works out for ya.
  10. kloner

    Camera slider with motion control. $450

    you got my mind thinking i need this thing with respect to Emos has first dibs..... does this kinda stuff, right?
  11. kloner

    Become A Model Aviation Mentor. Help Others In Our Sport!

    you can put me down for San Diego CA. I'm AMA, or not, multis, Single rotor, plank, specificaly into fpv steve@kloners.com
  12. kloner

    Naza GPS and Futaba 8FG and R6208SB RX not playing nicely together.

    i've built two discos with that radio and never seen the rx cause problems. But you mentioned des, he had a faulty rx with his radio that caused a bunch of grief, i'd start looking at it from that angle. maybe contact futaba and see what they say. only thing i've seen make 3 reds never go away...
  13. kloner

    Battery & iCharger 306b related questions

    When you ask what charge rates, just depends how big a hurry your in and how much IR increase your whiling to accept created by doing so. Your charger has the IR measurements, do the lab yourself and tell us what you find. I'm not sacrificing hours and batteries to find the answer. i usualy...
  14. kloner

    Kloner, your Suppo motors

    I never had one that didn't run smooth new. never crashed cause one acted up, but i never ran one that broke a prop. if the tip touched something, it got a new motor and that 2814 swap was less than $20. Great for FPV but i wouldn't use them profesionaly. I just recently threw away 17 of em i...
  15. kloner

    Before you buy, please read this

    that zero uav setup is similar but not so buggy did you catch the post from dji tellin us not to use 5.18 at all and to revert back to 5.16, like last week?
  16. kloner

    Basics of Setting up Eagletree elogger and OSD PRO on a multi-rotor

    there is an option for number smoothing i think they call it, is that turned off? might be called averaging, adjusted from the interface software in my experience it's a short when they jump around alot, esp at idle. it can be a winding and motor screw, i've had it be a magnet pop loose from a...
  17. kloner

    Hoverfly Today's excitement, Hoverfly PRO beta firmware first flights

    nice, sure hope i can get the alt hold part to work. takes alot of work out of a nice level flight
  18. kloner

    Basics of Setting up Eagletree elogger and OSD PRO on a multi-rotor

    1) yes. if it's high amp draw and a paralel battery run it between one battery and the distro board 2)you won't run any of the throttle, ail, ele, rud through any of it. that is all for return to home and it's not multi rotor supported, yet 3)put on whatever connectors your gonna use, the out...
  19. kloner

    GoPro Hero 2 for FPV camera

    yes, ritewings. i got 60" zii, 70" ZXR and 81" ZXL in the fleet. the zxl sports the nex5. the zxr is a 130mph plane...... all of em are long range fpv type you get them from ritewing. The covering you saw is vinyl like I show above except it's printed carbon fiber...
  20. kloner

    Hoverfly Hoverfly PRO and Opto ESC's

    is the ice esc opto? you have the red wires from a castle plugged into the hfp? mine wouldn't do that at all, tried taking the grounds away like my other rig and that made the esc's go blank and not boot.
Top