Search results

Thanks Rick.. got there in the end.. I just was confused about the BL allocations but Sandor has explained it below.. Once I had figured out how he had set it up I re-did the BL's I had replaced as built.. she's up. Bart... its awful lonely some times stuck with a problem that know one can help...

PS to Sandor... done all flashin of firmware via bluetooth no mither ;-)

DroidWorx Europe Thanks Sandor.. got it figured.. took me a bit of time to understand how the dis board was set up with the BL configs different than the Wiki but worked it out. SHY FLIES! I did save the all the settings when I origionally got it from you.. it was my fault for not taking...

OK Now I have reloaded the firmware for the nav and fc I have the motor test running. NOW may be my boob but when I start motor 2 2 & 5 run!!!. I am sure I have soldered the correct allocation pads but I will go check.. could it be anything to do with the mixer set up? I wonder alone :(

:confused:Ok story so far. Replaced bl 2 & 6 Replaced FC . Loaded 82b firmware Uploaded Hexa X3 config file Uploaded last flight settings Re flashed Nav 22a firmware. Error 18 still And BL missing. In Jeti Box I am getting error 3 (no comms between FC and NAV control and on the nav...

Hi Warmupper, welcome to MRF. Beautiful part of the world. May be you could post up your set up in the new members thread. Its always nice to see what other people are flying and filming with. Again welcome and I see you've jumped in theDW frame give-away good luck. Dave

Flamin harrold.. replaced BL6 and now I have BL5 missing! grrrr..Jeti Box can now see temps on BL6 but not 2 which is a new BL. Think I ll call it a night.. Any suggestions would be appreciated

Glad you found it... how frustrating.. As for the camera mount set up I would start a new thread. I will help as much as I can because there is a couple of things you need to make sure you have set for the Y6 other wise your mount will do all sorts of crazy things. I think I have it on my...

Ok replaced fried BL.. got all motors spinning up at motor start. :D Still BL control and FC error :( My jeti box cannot see temps on motors 2 and 6.:( Jeti box cannot see compass heading :( I am beginning to think its the FC as it looks pretty corroded in places Back to the garage:(

Well stripped down electronics, swapped out BL2. all green lights on bl dis board now but still same messages. green light on FC, green and red on nav board, green light on compass. Debug screen says FC and BL cntl board fault red, nav board and MK3mag OK green

Very nice looking quad there... any more info.. BTW welcome to MRF.. would be good if you could post some stuff about yourself in the new members thread Dave

Found this Status info Version .82b 0x00 0x02 0x00 0x00 0x00 0x00 BL Ctrl missing (check connections and mixer setup)

If it dont then just turn it upside down and use it as a coffee table... looks very nice and very well made... bet that would get airport baggage handlers curious!

I have got my ADX 3 build back up thanks to Geoff at Quadcopter UK but now have the electronics to sort out. This is the state of play. On the hexa distribution board BL#2 has a red and green light on. All others are green. All motors except the one attached to BL#2 spin up. These are...

Nice Ken.. Glad the Droidworx is at the top of the bunch.

Could be the connector. i know if the connector in your picture on my USB connection is not FULLY home i get a no connection message.

Sorry my mistake thought you meant the pics!

Got to give it to you Ken.. you certainly are a glutton for punishment... we'll all watch with interest.. What does the ultrasonic thingy do? Dave

Are your pics spotty as well? Are you going to post some examples? Dave

Yo JT nice pic. They look like veins! Interesting. Not sure of the Geology down there but it looks like semi porous and none porous rock formations below the surface the porus allowing the water table up to the subsoil allowing the wheat over the seams to get their water.. PS quick fact the UK...