Search results

Hi guys, Have problem how to wiring t-motors with t-motors 30A ESC. Is there specific procedure or you can random solder wires from motors to ESC, because all 3 wires from both motors and ESC are black. If I compare Gaui wiring there is black, red and yellow wire. And for 1,3 motors goes...

That I fear the most...

Will do that. Basically can use any OSD just to display info on screen. Thanks. Vojc

Hi Boris, Thank you for that value info. So then, what kind of OSD you prefer to use with my setup. Have 2 setups Naza-quad and WKM-octo. What kind info I can see with OSD? Basic info like: Voltage, mAh, direction, altitude, ... sorry for newbee question, but rather ask now, then later...

Hi folks, Searching on web with no luck yet for info if DragonOSD v2 Combo is compatible with Naza or Wookong? DragonOSD v2 spec info link: http://www.nghobbies.com/cart/index.php?main_page=product_info&cPath=1_38_161_162&products_id=687 For that money I think best value OSD with tracking...

On my GAUI 500X have naza in COD but it always fly backwards. When I put naza back side on plate then and start flying It total different story, stabile and easy to fly... don't know how, just saw some DJI guys that are tested Naza and notice that have also Naza in back side of the plate...

FINALLY Get quad hovering... Place MC just like show on video 2 (figure 1st from right) and push battery a little forward (figure 2nd). That's it. Upload some img for better imagining. Thanks Tomstoy2 & Lifter for push me a little bit forward with tests. Outside testing will be after...

Can not believe that precision... Yes it is by default. You can not assemble without tilt it. Good point Tomstoy2. Well I will do that. Thanks for advice. I'll be satisfied, if must trim all over the place, but always in one direction that's bother me... also re-position Naza all over the...

Even with moving MC forward not help. I'm running out of idea what cause that malfunction... Maybe begin from scratch... Thanks for support.

Today switch ESC and motors, but problem is the same. Also put battery above and bellow the quad and measure COD again to ensure is the quad on COD. Fly with weight of 1.950g, but direction is the same. Later today will try move MC slighty forward, maybe re-position of MC will help...

Thanks for suggestion, but check COG also (att. img.). Can't get Naza on very center of COG, because of the Lipo battery. When Attach Lipo on the bottom of quad then COG goes lower, right? Is this can cause the problem. Now I'm replacing motors and do test and report for about an hour or more...

Hi Tomstoy2, Triple check everything you said, and it is in place as should be. Confuse me the fact when apply only throttle stick gaui starting to move every time in one direction only (backwards). Completely different story would be if it moves in random direction. In the following video I...

Today do some more tests about trimming my Tx. Notice that Tx have also sub-trim, so enter value there and put quad in the air and it worked. Not Rock Solid, but hovers 100% better then before. Anyway Thank you guys for all support...

I agree and have more depth...

Thanks for advice, but I know for other stick combination.If you close look at the attached image all combination starts with stick down and that is in my case the problem, coz if I turn right stick down it goes just 85% (trim 15% up)...

Today did some test hovering with Naza. As I said before, when add only throttle quad lift up ok but slowly start to fly in backwards and left. I and quad stand nose front. So then I manually trim my Futaba Tx (15% front and 8% right). With this settings hover 100% better then before, but...

Hi there, First of all what kind of system you use. WKM or Naza? If you use WKM just turn off Voltage monitor restart your flyer and error will be gone. It is not good. In the following link are the steps you can safely use read from post #7 / point 4 link A week a go buy voltage telemetry and...

I think with 4s battery you will get more time and most important you can payload more.. but in other heands 4s lipo weight more... I have Zippy 4S 5000 mAh 40C and quad with lipo weight is about 1.300g and fight time on normal turning commands (training for AV-video) is 22min. No sudden turns...

Thanks for quick reply, Have Naza in COG position, also triple check motors (spining, angle,...) also tune ESC with Gaui manual: Battery type and timing set: Nimh/Nicd (2 beeps) All other settings to 1 beep. Maybe must tune props? will do that. Ok now I get it. Well then this is normal...

Hi guys, After crash with my GAUI 500X and WKM order same frame with Naza. Setup go smooth, but when I try to position hold and hover must trim my quad all the time. If I go in front direction and then release all stick quad start to accelerate in backward direction. Have played with gain...