Search results

I use ImmersionRC 600mW 5.8 VTX with stock antenna for my fpv. I have placed the TX on top of the quad with antenna pointing 90 degrees upwards. The video is not clear and gray while flying. I guess it may be because CF plates under the VTX which block signal. Would it be better to place the VTX...

I am going to use ezosd and current sensor,4s 6500mah lipo. I would like to land the aircraft when 80% of the pack capacity remains (1300mah remains or 5200mah is used) and the voltage is 3.7 per cell or 14.8 v in total. The manual is a bit vague for me. 1-Should I set Low Batt Alarm to 14.8v...

Sorry I did place wrong link for the mount. Check this one. http://www.cnchelicopter.com/servlet/the-2276/xaircraft-x650-special-upgrade/Detail

Hi Totality. I use following setup: Tiger Motor MT3506 650 kv http://rctigermotor.com/show.php?contentid=142 AKE 30 amp ESC http://www.cnchelicopter.com/servlet/the-2239/Multi-rotors-aircraft-AKE/Detail Motor mount http://www.cnchelicopter.com/servlet/Categories Prop...

BorisS, Thank you for your advice. I did recheck all plates under motors too see if I have placed them on the correct side after changing ESC’s. They were indeed on the correct side, but I found another issue which I’m a bit ashamed to tell. Two arms witch were marked X were placed to the socket...

I got the same yaw issue with S800. I never flied S800 until I received replacement ESC’s last week. I replaced them and maiden yesterday. After takeoff the bird yaws about 20 degrees to the right and hovers at that position. It doesn’t continue yawing around, just 20 degrees to the right and...

Regarding question 6. I have tested to fly (in simulation mode) only using data link. The TX was off from beginning. I have not tested this in real mode yet, but I guess it should work.

I have some experience using Joystick + WKN single way point and 900mhz data link in simulation mode (not yet in real mode). My purpose is to free my TX and RX and use them to control Z15. In simulation it works OK. You should practice and get used to it. I proceed like this. First start the PC...

Solved. I put the idle speed to highest position in WKM software and now all motors run at the same speed.

I have installed WKM on a quad. Two of motors rotate slower than the other two by random. When I disconnect and reconnect the battery, the motors with slow speed become normal and the other two become slow. I have calibrated all ESCs one by one by connecting them to the throttle channel. Any advice?

It happened to me once and I realized I had triggered home lock and course lick button.

Tahoe Ed I appreciate your advice and the picture. Now I have to wait to receive ESCs and then start the challenge of replacement.

Dji just informed me that my S800 is among those which have faulty ESCs and they should be replaced. Dji will send me replacements. I wonder if I could be able to replace them by myself. I can solder wires to connectors but I have never soldered wires to electronic boards. I am wondering if it...

Has anyone tried this? http://www.cnchelicopter.com/servlet/the-2276/xaircraft-x650-special-upgrade/Detail Please share your experience about motor, prop, esc, battery setup and flying time.

I am glad to hear maxamps would power everything for 14 mins. I use Quanum telemetry since my Radio (JR DSX 11) has no telemetry. The use of data link has two benefits for me. It covers longer range. I can fly using a Joystick so the radio could be used by the camera man.

Thank you Tahoe Ed. Very good point. Thanks God when I was buying the data link the dealer had only the 900mhz in stock and I did buy it even though it was a little more expensive. So the can port problem is solved for me :nevreness:

Thank you DennyR. It’s very disappointing to see that I have to choose between Zenmuse and the Data link. Unbelievable! I am still wondering if it is necessary to buy a separate battery for Zenmuse z15. I have ordered Maxamps 6s 11000 mah for S800. Would zenmuse share the power or requires...

Any advice is appreciated.

I have not Zenmuse yet but I wonder how I should connect it to S800 when I receive it. S800 has a dedicated power cable (XT60 connector) which should be connected to the gimbal. Hence the gimbal and s800 will use the same battery pack. Am I correct? If it is correct, I wonder how much the...

Until now I had turned off the voltage monitor on assistant software because I do not intend to fly the aircraft until all hardware and software setups are properly in place. I just test the system with a 6s 3700mah lipo which I already have. Today I activated voltage monitor on assistant...