Search results

Hi Guys, Thank you very much for the reply.. I realize the monitor is purely for framing but my gimbal operator is struggling to tell the difference between dustbins and humans. :nevreness: I also thought it could be my transmitters not doing a proper job hence the test where I bypassed the...

Hi Benjamin, I purchased the same HDMI converter as what you have/use to sell but I'm really struggling with the image quality that I'm getting from it. I'm using a GH2 with no hacks. What is your image quality like that you get on the composite side? If it is good then I suspect my unit might...

Redridinghood, I agree with what you are saying, it makes sense that the motors will get hotter as they are compensating more while trying to keep the craft stable. I'm still going to be doing the test purely to see if they are drawing as much current as I think they would, because if they draw...

Hi Elliot and Redridinghood, Thank you very much for the replies. I've been doing a lot of research into this and I've come to the conclusion that the 14" x 4.7 props are not too bad, they are not ideal but not bad. In my research I came across "1001 Copters" where Catlord did and extremely...

Hi StormRU, I had a couple of ideas but I finally settled on what I think is the simplest option (will take pictures tomorrow and post here), I simply connected the battery trays together in such a way that I could remove the 4 centre stand-offs used to secure the battery tray in the middle. I...

Hi Elliot, I'm having the same problems, I have six AXI 2814-22 with 14" x 4.7 props. I found that three off my motors get really hot but I think it is due to my gimbal being slightly tail heavy so these motors are working harder than they would normally. Have you found any answers yet with...

Hi All, OK in the early hours of this morning I discovered my problem, pure human error. The esc cables in my wiring loom were marked incorrectly so some of them did not end up in the correct ports on the HF Board. I've managed to sort out the problem and I have had some very good flights...

Yes I would advise you not too, I left my gimbal off as well luckily. I'm thinking of changing out as many esc's as I can tomorrow morning first thing to see if it is not maybe one of them that is faulty.

Hi All, OK still no luck my side, I swopped out radio's - tested and it still flips. Reprogrammed all the ESC's - tested and still flips. Placed a small beach of open cell foam on the board - tested and still flips. Down graded the firmware to the latest version 3 - tested and still...

I find it very strange as I used the exact same board and TX on my quad and it flew like it was on rails.. I'll swop back to my old TX and see if that fixes it. This really is a very strange incident. I've logged a ticket with the Hoverfly guys as well so lets see what they come back with. What...

Hi Bart, I did both the Temp and accelerometer calibrations, but still the problem persists, took it out yesterday and it flipped again. I'm going to double check that all my ESC are programmed correctly but I don't think that is the problem. Any more ideas anybody? Regards, Andre

Hi Bart, Are you referring to the Temperature and Accelerometer calibrations? I did not redo those, I swopped the board from the Quad to the Hex and just changed the frame configuration under the "Pro Info" tab. Is the calibration required every time I swop frames? Andre

Hi guys, I seem to be experiencing the same problems on my HEX, I have the Hoverfly Black board and I'm using a Hitec Aurora 9 TX. I took my quad out first with the HF board as I'm testing the new Aurora 9 TX, I ended up flying around a little to get the best Gain setting which I thought was...

Does anybody out there use the Aurora 9 TX/RX?

Hi dckiteboards, I've had something similar, question I have for you is do you have you "gear" channel plugged into the HFP board? Mine did something similar when I had to steal a channel to run my Gimbal as my Transmitter only has 6 channels, I unplugged the gain channel as I still wanted...

Hi Benjamin, Any update on how everything is working with the HF Gimbal and the Cinestar combination? Have you managed to film anything yet? Really looking forward to seeing what it can do, I have all the equipment now just waiting for the signal conditioners to arrive then I'll start setting...

Hi Benjamin, Thank you very much for the feedback, I've actually thought of a solution just waiting for some parts I'm getting cut. Once all assembled I will send a picture.

Raising the board isn't the problem unfortunately. The space between the standoffs isn't wide enough for the board... any other thoughts?

Hi thanks for the replies, I've attached two photo's which shows that the hoverfly boards are clearly too wide to fit under the battery tray on the cinestar 6. I'll need to put some thought into it to figure out how I can get around this.. Benjamin, can you please send me the exact link to...

Hi Guys, I just received some new really cool Kit on the weekend. 1 x Cinestar 6 including 360 Gimbal. I've been assembling it and I must say it is a really great piece of equipment. I need some information, I've noticed that there are some people in the community who are flying the same...