Recent content by SirMj

A2212 1000KV Brushless Outrunner Motor & 10x4.5" props

self level, thats why I was so shocked I mean i get the fact that it might be pitching or rolling somewhere but the inability to at least keep altitude was very annoying. and yah it has good reputation and a lot of videos show real good hover and control. but I am having a whole different story...

I went out for a test today, and did launch it it does fly but needs a lot of fixing since I have noticed that the motors dont run at the same speed. and I calibrated them probably a million times. oh and one more thing, it never stays in hover it's either going up or its going down

I have been working on this quad for quiet sometime, and during that time I have triple, quadruple checked the combos and their channels. and yes the calibration sound was a beep then double beep after throttle down then music then it works. that happened to all ESC's

Hi guys this is my first quad copter. Some specification : F450 body 30 Amp simonK ESC 1100kv motors (i think haha kinda forgot) 10 inch props and they are balanced KK 2.1 flight controller. battery Zippy - 3000 Mah - 20 C Flysky FS-t6 transmitter and receiver I did the calibration with KK...

Hi everyone, I was excited for my first flight after getting everything together but the KK board started with a sound and back light only , without any writing (KK board is new i have tested it once few months back and it worked). I tried changing batteries thinking might be voltage but it...

at last i found someone who started like me. and yes i spend crazy late nights searching till at one point I looked at the time and it was 5 am. thank you for this its very helpful . the receiver is the last piece to the puzzle and now i am almost done. thanks a lot. and to all that helped me I...

I didnt want to make a new thread so i hope someone would read this. I managed to salvage this Futaba T6EXP . sadly without it's receiver . what are the possible ways to bind it to a receiver. ( can it be a different model or different brand OR can it be a different number of channels like...

great compliment made me rethink throwing it in the trash . although I am already designing a 3D model in hope of 3D printing it and using it. now that I am actually doing it . the challenge is great that video was greatly helpful . which makes me want to make the same experiment at my uni...

I have been asked for pics on the 2nd thread that I have . please visit and see it . http://multirotorforums.com/threads/finally-i-am-here.24101/#post-199098 you wont be disappointed because when i say ugly , I do mean it :p

I did not expect such a warm welcome . thank you very much please excuse the quality of the pictures it is the best I can do at the moment. I have not connected everything yet since I am still thinking about what changes that I need to make . One of my biggest problems at the moment is...

I think you're right. and I might just borrow a transmitter for testing until my budget gets on its feet and i can get me something that would last and fulfill the need . the hardware with weight: KK 2.1.5 Flight control board / 21 gram SimonK 30A ESC With BEC / 100 gram 1000KV...

Yes I have thought about uploading pics and that will happen as soon as I am able to. as for the Walkera its for 45 dollars. and the real reason I thought of it, is because its easier to acquire considering the fact that I am really excited to get this airborne. while buying any other radio...

After going on and on in my mind about joining a Multi Rotor forum . I finally gathered the courage to to this. HI, I am MJ. and the only thing i know about Quads is that they look cool flying. which probably lead me to the biggest mistake of my life. building my own -.- Anyway I am facing...

Hi guys. I have just joined this forum. and I'll post on the introduction page soon after. I am on the verge of completing my first (Ugly as hell, most messed up) Quad copter. I will enlist my hardware bellow. My problem now is that I am trying to buy a transmitter. considering the fact that...