Flying Cinema CineTank with XAircraft SuperX

[Motopreserve]

I began documenting this build with the frame assembly, which can be seen over in the review section. Of course, the build just starts with the frame, but I realized I had not been updating my progress, and follow-up thoughts to the choices I made for this quad...

It's been about a month since I first put the frame together - and finally some weather worked in my favor, and I was able to get out to the field for some flying. More on that tom come...

First thing I needed to do was get all the components onto the frame. I had decided to go with the SunnySky V2816-1250kv motors. The V-Series is pretty sweet, with pre-cut shaft, and extra long motor wires (600mm, no bullets). The quality of these motors in your hand already feels better than the cheapies, and once you get them installed, there is a confidence they inspire. I haven't used any other super-high end manufacturers yet (T-Motors, Avroto etc), but these felt pretty damn high end to me.



I got all the ESCs and wiring laid out and installed. The fit in the "dirty" section of the CineTank is slightly tight for the f-30a speed controllers I used, but they ended up fitting nicely.



Once the basic parts of the frame were together, the SiuperX was installed. In the photo below you can see the side-view with the SuperX tucked away inbetween the 2 clean section plates. The pink rubber balls are to isolate the dirty and clean sections, removing motor vibrations from the clean section where the camera will sit.



Flying Cinema recommend 8" or 9" props. Once I got the 9" on there I was a little worried that they came mighty close to the frame. But when you peek a little closer - you realize they cut the frame plates specifically to allow for these size props.



Everything at first has been somewhat temprary as I waited for some cool parts that will add to the build quality. In the photo below you can see the GPS puck, which is HUGE! is just strapped to the top plate with zip-ties.



Stay tuned for updates...

 

[dazzab]

In the photo below you can see the GPS puck, which is HUGE! is just strapped to the top plate with zip-ties.
Stay tuned for updates...

Looking great! I secured my GPS puck with Scotch Dual Lock. If you haven't tried it before it's great stuff. Unlike velcro it clicks in place and is 15 times stronger. Perfect for things like this puck.

 

[Motopreserve]

I ended up getting a stand/riser for the puck that was 3D printed. I knew it was coming - which is why I just slapped it on like this. Then it took a while and I ended up making one myself with some shapelock mold able plastic. Didn't look great - so I'm glad I now have the other one

Ive heard of dual lock. I always keep my eyes peeled for it at the hardware stores, but I really just need to order some from the internet.

 

[SoCal Blur]

Down the road you might consider getting the AerialMOB TBS arm extensions or at least some longer CF tubs and using some larger props. I like the TBS discovery but the Pro version costs more than what I spent building my Octo. The Cinetank seems like a good alternative. I also agree with you on the quality of the V series SunnySky motors.

 

[Motopreserve]

Down the road you might consider getting the AerialMOB TBS arm extensions or at least some longer CF tubs and using some larger props. I like the TBS discovery but the Pro version costs more than what I spent building my Octo. The Cinetank seems like a good alternative. I also agree with you on the quality of the V series SunnySky motors.

The boys over at flying cinema are going to have extended arms for this quad. They are currently waiting on their supplier. I could get carbon booms anywhere I guess - but they are using a particularly strong type and will be offering them as an upgrade at a reasonable cost. I think larger props would require smaller motors too, so I'm ok with the delay at this point...or at least my wallet is.

Initially my I wanted the longer arms right away. But the more I fly this thing (tuning notwithstanding) the more I feel it may be best right where it's at. It's pretty nimble. I'm swapping a multiwii 3 mini onto it soon, and will see how that effects it. The superx will be going over to the hex.

 

[SoCal Blur]

The boys over at flying cinema are going to have extended arms for this quad. They are currently waiting on their supplier. I could get carbon booms anywhere I guess - but they are using a particularly strong type and will be offering them as an upgrade at a reasonable cost. I think larger props would require smaller motors too, so I'm ok with the delay at this point...or at least my wallet is.

Initially my I wanted the longer arms right away. But the more I fly this thing (tuning notwithstanding) the more I feel it may be best right where it's at. It's pretty nimble. I'm swapping a multiwii 3 mini onto it soon, and will see how that effects it. The superx will be going over to the hex.

Oh, good. Sounds like the Cinetank folks are on top of it. Out of curiosity, what did you end up with with your "P" on your PID tuning for Pitch and Roll (for the chopstick quad)? Will you start with the same settings on the Cinetank or do you think you'll start from scratch? I don't know how close they are in weight.

SuperX to the Hex, huh? Did you end up getting the Tarot?

 

[Motopreserve]

Oh, good. Sounds like the Cinetank folks are on top of it. Out of curiosity, what did you end up with with your "P" on your PID tuning for Pitch and Roll (for the chopstick quad)? Will you start with the same settings on the Cinetank or do you think you'll start from scratch? I don't know how close they are in weight.

SuperX to the Hex, huh? Did you end up getting the Tarot?

i don't recall where I was at with the PID settings. I'll check when I plug it in next and shoot you the settings. I remember I went back to the default starting point after messing around a lot - and did t change too drastically. I'll definitely start fresh on the cinetank - it's a whole different animal.

 

[Motopreserve]

Speak of the Devil....

Longer booms available now. Check out the Flying Cinema site for DETAILS.

 

[SoCal Blur]

So now you can move up to 12" props. I imagine that would increase your flying time a bit.

 

[Motopreserve]

So now you can move up to 12" props. I imagine that would increase your flying time a bit.

I have enough craziness going on right now...trying to show restraint

 

[Motopreserve]

Getting ready to tear this thing apart and start from scratch - making room for new FC (Multiwii mini-Pro), FPV gear and a different PDB setup. So I have to go all the way back in, take it all apart and get it straight.

I don't know if I mentioned it before - but if anyone is interested in this frame - you can order it directly from Flying Cinema and get free shipping (CONUS). I think all the other retailers don't do this deal. Also, it seems they may be selling the frame with the new, longer booms in a kit called the "L" version. That way if you want to run up to 12" props right out of the gate, you'll be all set.

Stay tuned...should have some progress this coming week...