Search results

How do you go about running the naza v2 with the v1 VU? And not using the v2 PMU? I saw sander mention doing it, but was also told the v1 VU won't indicate what mode the naza is in.

Love this little guy. This is the third quad I've built and IMO it's the best of the bunch. Specs: QAV400 Tiger MT2216-9 1100kv motors 30a DYS simonk esc's OP CC3D Dragon Link UHF 300mW 1.3 vTx Bluebeam Ultra 1.3 antennas Gopro3 pz0513 flight cam 8" carbon gemfan props zippy compact 4s 25c...

I'm assuming this gives you more range vs a regular 2.4ghz Rx? http://team-blacksheep.com/products/prod:ezuhf_rx Using a futaba t8j and r2008sb. What could I expect with replacing the r2008sb with the EZUHF? i would need this as well? Attach to the 8j...

Have the three way CM switch setup, IOC switch setup, FS on signal loss set up. Having problems with the Forced Failsafe switch though. I can get GPS and Manual into FS, but not Atti. Here are pics of the program mix. GPS Atti Manual Any suggestions?

Stripped down my f450 in preperation of my tbs disco build. All that's left on the bottom plate is the battery plug, vu, and naza. Just got my futaba 8j in and wanted to get the naza config started. I binded the Rx to the TX, powered up the naza, plugged x2 into the sbus, started the naza...

Debating if I should do it during the rebuild. Saw a vid on youtube where a guy just moves a piece of tape around on the motor until the vibes decrease using a vibration app then he adds tape to that spot till their just about gone. Didn't look to hard.

Question. Do I have to change any of these programmable items: Brake setup: Disabled Startup mode: Normal (options soft or super soft) Timing: Low (options medium and high) I know I have to calibrate the throttle range

I'm thinking I should get something like a mini mic. The thought of not being able to hear anything doesn't sound right to me. Even if I just hear the motors spinning, I think it will be a better experience ?

How's the range on this combo? I'm using a devo10 100mw Tx right now but I'm concerned about the range since I will be flying fpv. This looks like a good deal? http://www.ebay.com/itm/Brand-New-Futaba-8FGS-8FGH-8FG-Helicopter-Version-2-4ghz-Fasst-RC-Transmitter-/281011425071#vi-content...

Hey guys, Have a brand new cam that I wont be using. You can see it's still in it's shrink wrap. Price at RMRC is $100 plus shipping. I'll sell it for $75 shipped

I'm looking for yellow and black. When looking online they sell it in 5m lengths. I only need about 12" of each. I'll buy some off you if you're willing to send. thanks,

Hows the efficiency compared to 22mm 900kv's? Are you running the 30a opto esc's? The motor is 35a that's why I ask. Would I be a lot happier with the suppo compared to the 22mm tigers?

Hey guys, I have 4 of these batteries that I'm was planning on using for my f450. I have wrapped them in carbon fiber vinyl wrap and soldered deans connectors to them. I want to get bigger batteries as I plan to convert my f450 into a TBS Discovery. Planning on getting (4) 4s 4500mah...

I have 900kv t-motors. I believe they are 20a max. So if I have a 4000mah battery x 25c that would be 100,000 milliamps, or 100 amps. So 100amps I can draw off the battery. Four 20a motors would be 80a max draw. So a 4000mah 25c battery would satisfy the max amp draw for a quad with 20a (max...

Does it snap off or do you have to remove the screws underneath? Looks like t5 torx?

Just curious ?

Would there be any noticeable difference between the two? The Disco esc's are flashed with SimonK's FW and supposedly don't have the problems that other esc's have when flashed with the firmware. I plan on ordering a TBS disco frame and will use my 900kv motors, don't know if it's worth it to...

In GPS mode, when at 45-55% throttle, the quad once to slowly rise. I didn't notice this the last flight. I'll bring it about 3 feet off the ground at 50% throttle, and it will slowly rise to about 10 feet. Should it not just stay at the same height? If I pull the quad away from its position of...

Just want to be sure I understand how to do this correctly. So, I'll need this switch: http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=8833 Plug it in to the gear channel on my Rx. Then on the other end of the switch there are two wires. One I solder to any positive lead...

What do you guys think of the new look?