Search results

looking to build back up a octo cinestar and just have it on the desk in the office anyone got motors that would fit it and 12 inch props? thinking cheap. ill pay shipping Thanks C they dont have to run

I have both of these items for sale they are used but well taken care of. $100 bucks shipped

I have a Beholder Gimbal I bought a year ago that I assembled and never had a bird to stick it on. I dont think I have the box anymore but works perfect still! was thinking 110$ shipped

I have a bunch of stuff I am just not using and thought id trya nd sell it on here. spectrum dx8 with box and telemetry and possibly a ar8000 $300 A bunch of props maybe buy the whole lot for 60 bucks? 11x4.7 SF 12x4.5 hyperion 720i charger $70 exceed proton 30A brushless...

I have a clean dx8 tx that I don't use anymore and can include a a8000 rx I have the charger and battery included and both work well. Full box and most original parts inside Make offer ? I'll update later with price . 300?

I'm finally selling the hoverfly board as I don't use it anymore . It's used but treated well never crashed . Was thinking 150 bucks?

this seems like its just a great idea! multirotors will chop fingers off and this will take a small block out! http://snapwidget.com/view/?id=493583085404457080_19132849&fb_comment_id=fbc_612295118794957_6823365_616604871697315#f2abac1cdc WTF!!!

everything is working perfect however when i go to throttle up the heli lifts off the ground perfect and then you realize there is absolutely no control's ail,rud,elev??? it reacts in the setup client? maybe just reflash firmware etc? motors are all spinning correctly as well! thanks...

Multirotors are so dangerous at timestamp 4:02

EXTREME! skip to 1:47

I updated everything and now it's having a hard time connecting. Says searching com port 14 and it goes down to 2. It connected once for about 10 seconds and then program became unresponsive. I rebooted, updated the firmware for recognizing the USB . Everything worked perfectly before . I'm...

So a couple days ago I heard through some friends that in a couple weeks during a upcoming very popular festival there will be a man with some sort of rc helicopter to drop ping pong balls filled with prizes over a possible crowd of people being 500 to 3000. I immediately did some digging, and...

now when i try to connect to the setup utility it says"searching COM10 " and then the program becomes unresponsive and requires a shut down!

so im terrible with all the technical things with this hobby, i have only been doing it for two years. so i bought these http://www.hobbyking.com/hobbyking/store/__19611__NTM_Prop_Drive_28_36_750KV_265W.html thinking theyd be little less powerfull than my tmotors 2814 770kv they...

Three battery packs+one subject+short sunset= pretty neat

ok so i received my dx8 back from horizon hobby and they did in fact replace the gimbals? anyway whatever they did seemed to have brought the channels back to zero.. any way put up the bird today and it will fly but rudder to the right? heres a flick thank you Chris

i have the HVP black board and i finally got it to arm. now i am having problems when im just under quarter throttle looking good like it will lift off it goes FULL power right upside down! im going to calibrate the board again and see if that changes . im using a dx8 ar8000 tx rx??

So originally i wasnt able to arm the hoverfly pro . I figured out now if upon plugging in the battery i move the stick to the top and then bottom it will boot up and allow motor movement. However the motors wont spool up to full speed, so im assuming i incorrectly setup the throttle range on...

Bought the hoverfly pro today as well as the exceed proton 30 amp esc's I googled a bit before doing the esc's, is this going to be a decent combo?

More FAA talk http://photographyforrealestate.net/2012/01/24/warning-faa-says-us-airspace-is-closed-to-all-commercial/?utm_source=feedburner&utm_medium=email&utm_campaign=Feed%3A+PhotographyForRealEstate+%28Photography+for+Real+Estate%29