Search results

Quick question, will the self tightening props work on the P1 V1? This was the first one on the marked.

Thank you so much :):)

Will these work with the NAZA http://www.ebay.com/itm/Hobbywing-Pentium-30A-Brushless-Motor-Electronic-Speed-Controller-ESC-5V2A-BEC-/320942133430?pt=LH_DefaultDomain_0&hash=item4ab9a450b6 These are V3.1 I see, or do I need the FunFly ones?

I had all kinds of problems with my X650V4 with the Naza, also the one you describe, it all landet on the motors not being level with eachother! The holes in the X650 arms has some play, it ain't enough to just put in the screws and tighten them down. I took off the landing gear put it straight...

These would be the ESC's I wrote about in my firstpost :)

Something has happend to one of my hobby wing ESC, out of 4 one acts like its crazy. Tested it without the Naza and only a RX and it acts like nothing I have seen before. But to make things easier with wires and stuff, I thought about buying 4 of these...

Motor with the vibration is changed out, props are balanced, gains reset, but it still has the vibration/wobble at throttle up. And its rodeo like hovering ;) I'm beginning to think this could either be the props themself, that I have damaged them when I hit the door on my way out. Or it could...

In a previos thread I got a reply to buy Graupner el. props 10x5 as they have 8mm center hole and those would fit the original X650 motors, but they dont! I also bought some with 6mm and a 8mm prop reamer, but then that didn't work either :( Are there eny alternative props fitting directly on...

...

Yes, and I would like to make something looking as good as these! I dont want to trow some LED's at it with wires and all. I want the layout to be thought through. But this was a thread to see if anyone has done anything cool looking, I know I can put on some LED's and connect 12v to them.

NO, they are not, and NO they will not! http://www.xaircraft.org/2010/09/xaircraft-x650-quadcopter-led-module.html

As I'm slowly gaining hight I get less and less sight/control of my X650. I would like to add som LED light making it easier to orientate :) On my X525 I have put LED strips under all 4 arms, but for the X650 I would like to make something looking more thought through, and stealth ;) I see that...

Thank you both :) Then I'm back to a question I asked myself early in the build, should I change out the original 4 motors to some with a different shaft, making buying and balancing props easier? If so, what motor match the original X650V motor?

The #1 motor sure has a bad sound to it! Almost like it has a small stone inside. Guess it's the bearing going bad :) That could have been my problem all a long I would think, as it also had a slight wobble in air that I never got rid of :) Happy to find the cause of the problems :):):):):)

Yes, I think they do, also for other reasons. But would that make the problem appear after about 10 flights? Can it have damaged something not balancing them from the start?

I can't understand why it started to do this out of the blue! It has never been crashed, never gotten any hits, it has never even been landed hard. It only has about 10 flights in it, and all of the sudden it startet to shake at low throttle, WHY...

It also all of a sudden has some shake on power up, I can't find a solution to this!

I set mine to 1000 -1000 -1000, then it have full travel

I have tried everything, but from time to time my x650 get this shiver for a fraction of a second, then it's smooth again. The X650 is stock but with two 3S 2200 lipo. They are stacked on each other to fit on the battery plate, maybe it's get unstabil as this gives a low CG? But I read that if...

Thank you! Maybe try to adjust the aw gain some more then :)