Search results

  1. snurre

    DJI Phantom 4 Official Owners' Thread

    Looking for propeller guards for the Phantom 4. Are there dedicated guards for Phantom 4 or are they identical as for Phantom 3? Edit. Nope, tried Ph3 guards today. No joy. So where's the prop guards for P4? I noticed the recent FW update deactivates obstacle avoidance when it detects prop...
  2. snurre

    A2 receiver vs external. What are you using and why?

    Hi, 1) Mode 4(D16) 2) Yes 3) From the A2 X2 port. The A2 is supplied from its power module (and the PM goes directly to the main packs).
  3. snurre

    A2 receiver vs external. What are you using and why?

    Hi @saenzm, Sorry, but documenting my exact setup is just a but too tedious and I doubt you will need it. Regarding gimbal control: My project is yet not completed but the gimbal will be controlled with a dedicated radio, though i think it is quite possible to have it all set up in one single...
  4. snurre

    A2 vertical speed limit - I only get 4 m/s - why?

    Hi guys, thanks for the response. Yes the batteries are suffiecient. 2 * 10Ah 6S 20C. ESCs, battery and motors matched. I will put more time into this project soon and as the new DJI firmware versions are now released the OSD will once again be available for data logging and analysis. (this...
  5. snurre

    Phobotic Micropiece Controller

    Promising. Does the micro have the same feature set and connectivity ports as the bigger brothers? Will you offer encoder support? Sent from my iPad using Tapatalk
  6. snurre

    iOSD logs not showing

    Glad I found this thread. I was getting really confused and disappointed with this problem. Now I am just disappointed. I am on the latest firmware for everything, latest iOSD assistant / Data Viewer. Experiencing exactly the same problem you have described. So it´s the Data Viewer software that...
  7. snurre

    Phobotic Centerpiece Brushless Gimbal Controller

    Ok, I understand and I do appreciate this sincerity. Consequently, a reasonable conclusion is that this unnamed bigger gimbal is, for now, just as much hot air as the F1. With regards to interest assessment, I find the bigger one very interesting. Please keep us posted.
  8. snurre

    Phobotic Centerpiece Brushless Gimbal Controller

    Well Roee, sorry to hear about the termination of the F1 project. But I am happy about the good news regarding it´s previously secret big brother (F2?). With reference to the unexpected abortion of the F1 story, is this "F2" a firm GO on completion and release? And when would you anticipate it...
  9. snurre

    A2 vertical speed limit - I only get 4 m/s - why?

    Hi, According to the A2 spec. the vertical speed limits in ATTI and GPS ATTI mode is 6 m/s. But when I punch full climb on the throttle it settles at exactly 4 m/s only. Same with AUW 7 kg and AUW 11 kg, so it is not a performance issue. The throttle range calibration matches the A2 assistent...
  10. snurre

    A2 receiver vs external. What are you using and why?

    FrSky X8R and Taranis plus as TX. Wonderful programming options, Failsafe options, good telemetry with logging, RSSI and S/bus output to the A2. And 8 ordinary servo output ports (CH 9-16). I decided against "intelligent landing gear". I must be able to fly really close to ground, below 5...
  11. snurre

    A2/ Lightbridge Groundstation?

    As for using DSM2 - NO - I would actually advice against that. Mind you I yet have no personal experience of this specific subject, though I am facing exactly the same dilemma in my current build project. Anyway, DSM2 does not use frequency hopping but rather two "fixed" channels that the...
  12. snurre

    A2/ Lightbridge Groundstation?

    Good point. I guess the problem here is that the Lightbridge onboard TX outputs relatively high power, high bandwidth and high duty cycle and may saturate the poor 2.4GHz RC RX due to their close proximity (onboard the same vehicle).
  13. snurre

    A2 1.4 - losing altitude when flying straight forward

    I think the phenomena is also caused by, maybe even mainly, ram air pressure build up during forward flight. Assuming you have already tried tweaking the A2 controller gain for vertical control...?
  14. snurre

    A2/ Lightbridge Groundstation?

    I wish DJI would at least come up with a 433MHz ground station link, like this one from 3DR (they use a cheap and robust bulk radio module inside). Integrating GS link into Lightbridge would be even better though. DJI does offer a 900MHz GS model, but it´s useless/illegal here in Europe due...
  15. snurre

    The new F1 Gimbal (Air Studio/Phobotic) for GH4 sized cameras

    Ok, this is quite understandable. Thank you for the update. Please say your best guess for ETA. A guess that we understand is not a promise. Skickat från min Galaxy Nexus via Tapatalk
  16. snurre

    Inspire 1 Owner's Thread

    TahoeEd, I am trying to get reliable info on DJI platform policy with reference to the iOS, Android and Windows. The info fragments available on DJI public web site, including the forum part, leaves some uncertainty about it. I think most operators prefer to invest either in iOS platform OR...
  17. snurre

    Zenmuse GH4 Owners thread

    Just clarifying - the 16:9 12Mpix issue is on the Panasonic account, not a Zenmuse thing. As soon as a hdmi is plugged in to the camera it reverts to 16:9. Utterly st*pid.
  18. snurre

    Lightbridge AND waypoint flying

    Thank you Ed. So I guess DJI has not yet implemented the Lightbridge as a data channel for Ground Station communication. Do you know if this is in the pipeline? It seems like the natural way to do it. Tom
  19. snurre

    Lightbridge AND waypoint flying

    Hi guys, I am planning to use A2 and Lightbridge in my upcoming multirotor project. Intending to use Lightbridge for the RC link (one or two operator setup). I want to be able to use it for regular video shooting but also for survey photo waypoint missions. Will this work well? Or what...
Top