Search results

It's a version 5 and at the moment nothing is attached to it, I've just flashed the firmware and have done the calibrations and ready to move forward except getting that red led, I'll that a screen shot of the clearflight page I am on and post that tonight

sorry, its a solid blue led that i am getting with a flashing red

i am getting a flashing red light along with a solid green light when i plug my computer into the naze, i can calibrate the magnetometer and acelatrometer and can see that they work in cleanflight, just don't know what i did to get that red flashing light, any ideas, thanks

thanks for that, thats exactly what i was doing, going to s-bus set up, anyway, just watched his video, followed it step by step and bingo, it all works, just needed a couple of twiks and all is well, good radio, but can be frustrating at times, anyway thanks so much for the advice.

i am setting up 3 way and override switches, I've got the" SE "switch set for the modes, I can get the offsets for atti and gps to land on the right spots, but for manual, i can get manual highlighted on the assistant but when I hit enter on the radio the highlight slides over to the right side...

been very quite on this thread lately, whats up??, Ive finally pick the frame i'll use, a reptile 500, tbs clone, it comes with a 700 line camera on a tilt servo. Ill team it up with some sunny sky 2814- 800 kv motors and use a 4s bat, ordered parts today but won't get them for a couple of weeks

Ok, ill hop on the bus, what do you think about the xj 470 foldable frame, i was looking through some of the posts on MRF and it sounds not too bad, had some issues but that was with the early versions, 2 years ago, so they should be resolved by now. what are your thoughts.

Welcome Justin: the f550 is what i choose as well for my first build, i would recommend, its very easy to put together and get up and running, there is so much information on this site to help us out, and lots of videos to follow along with to complete your build properly. But, be warned, this...

k thanks, was just wondering, I thought that when you throttle up that the booms could deflect enough to allow the props to touch, and then bad things will happen, I haven't actually started the motors with the props on, so i guess thats the next step. thanks

when setting up my mode switch,and while in the assistant, when moving the blue indicator from gps to atti to manual, i could not get that blue indicator to hit the manual button, i can see it over on the far right side of the screen, but can't get it to land on the manual button, when i test...

picked up a f550 kit from hobby king awhile back, have been putting it together slowly over the last couple of months, in the instructions it it states that 10" props could be used on this frame, so when i ordered all the parts I ordered 10" props, when I installed the props I found that there...

oh i get it, all the assistant is asking for is the distance away from cg, which there is only one cg, vertical distance away from it depends on where you have placed the gps on the frame

i ve got my copter put together and now setting up the naza . but how have you guys calculate the vertical cg. Do i need to rig something to hang it off of to get the balance point? I am thinking the cg is somewhere in between the top of the batteries and the bottom frame plate. Am i going in...

k, thanks for that quick response, I have just finished that step, all 6 esc's seam to come alive at the same point just below the first indeed on the throttle stick, so all appears to be ok to this point, moving along to next step, the esc's came with bec, so need to pull the power lead out...

just received all the parts for a thunder s550 , started to put the frame together, now i am the point of calibrating the throttle limits on the esc's, but now I have a question . I am using afro 30 amp esc's that are supposed to have simonK firmware in them, the question is, after the throttle...

Ok so that's what I will do , attach the pmu leads to the esc pads, thanks, also there is a spot to attach a deans connector for the main power in, but I think I will scratch some paint off in that area and get the leads further apart because it looks like there would be a good chance for the...

just wanted to know how to connect power leads from a naza mv2 pmu board to the intergrsated board of a thunder S550, I was planing on sharing the + and - terminals of one of the esc connections, or is there a better way ?

hi to everyone in the forum, My name is bill from kamloops BC, i have just ordered parts for a first build, its going to be a S550 hex copter, going to run quanum mt 2814 at880 kv with afro 30 amp esc's and a dji naza mv2 controller gps combo also bought a Frsky Taranis x9d plus radio order it...