Search results

Here is a new FPV machine that I have been working on that incorporates a 2-axis brushless gimbal powered by the AlexMos Simple BGC, and designed specifically for the GoPro Hero 3. With one 4S 5000 mAh I get flight times around 10 minutes, there is room for two 4S 5000 mAh packs. Will post video...

New. 250 Euos+shipping /Jesper

Prototype cablecam with 3-axis gimbal that can fit large DSLRs. Requires tx/rx, and 3S battery pack to be complete. It is also possible to add stabilization through the use of a Picloc or similar. 800 Euros+shipping /Jesper

Originally from a Copterfilms gimbal. Diameter is 300mm, made out of FG. 100 Euros+shipping /Jesper

Never used. 120 Euros+shippig. /Jesper

Condition like new. 120 Euros+shipping. /Jesper

We have a used Galaxy oktocopter with a 3-axis camera platform for sale. It is in condition like new. It is sold with motors and ESCs installed (no other electronics included). This platform can be flown at weights up to 11kg (4kg payload). Price: 2500 Euros For more information please visit...

Does anyone know a source that has the RcTiger CF 14x5 props in stock? /Jesper

We have a used Galaxy oktocopter with a 3-axis camera platform for sale. It is in condition like new. It is sold either without electronics or with motors and ESCs installed (no other electronics included). Platform without electronics: 2200 Euros Platform with motors + ESCs: 3400 Euros For...

Brand new Hexacopter RTF (with or without transmitter). 2-axis camera gimbal. Built to lift larger DSLRs or video camras such as the SONY FS-100/700. WKM flight control, Picloc 3X for camera stabilization. High quality Mega Motors running on dual 6S 5000 mAh LiPos. Please contact...

After having built numerous quads and hexas, I decided to design a new octo with a 3-axis gimbal that would be able to lift heavier cameras like the RED Epic or Scarlet. We have now flown it with payloads of up to 4kg getting flight times of about 7 minutes. With 4kg payload, the AUW is 11kg...

We recently finished building a large oktocopter that's using a Wookong-M. It flies very well in atti mode, but in GPS mode it has made some sudden climbs and descents at a few occasions. The climbs/descent are quite rapid, but can easily be stopped by making the appropriate correction with the...

How fast are you guys spinning your APC slow flyer props? The recommended limit of 65000/diameter in inches=max RPM is very limiting. How much are you guys lifting with the 12x3.8SF and the 14x4.7SF? Can anyone recommend an alternative to the the APC 14x4.7SF Thanks, Jesper

When I set up the DJI camera stabilization I end up getting very slow corrections. For example: On tilt I have the gain set to about 20% to get the right amount of movement (to keep the camera plate level). This results in very slow corrections. If I increase gain I can get it respond much...

I have had some incidents that I think may be cause by the ESC battery and low voltage settings. What settings are you using? I am using Hobbywing/Plush ESCs. I heard from someone that its preferred to use NiCd/NiMh rather than LiPo, why? Just to eliminate low voltage cut-off protection...

What's the correct way to trim the WooKong? My machine want's to drift backwards and to the right. I am able to trim this out, but if I shut it down and then power it back up, it wont let med start the motors until I neutralize the trims. The machine balances quite well on the center plates so...

Has anyone seen any limitations on these props, or knows who manufactures them? Thanks, Jesper

I am building a new hexa (Y6)using Axi 2826/12. Anyone have any experience with a similar set-up in regards to prop selection? Thanks, Jesper

Has anyone one had any issuses using 2.4 GHz on their multis using CF frames? I am especially curious about Futaba users since there are no satellites rxs available. Thanks, Jesper

I have the opportunity to switch radios. I am also putting together my first WooKong hexa. What is the preferred radio system to use with the WooKong? I like the idea of using S-Bus to reduce the number wires. Are there any downsides to using S-Bus? Fail-safe? Any input is greatly appreciated...