Search results

this wookong? there are some good video tutorials of it on youtube have you downloaded the dji software yet? theres a manual there too, you reading that or just going for it blind asking as you go? http://www.dji-innovations.com/ look at "products" pick yours, then that page has software...

yep, and in assistant the sbus cable has the ch assignments i just mentioned....... the language barrier is too far apart

huh? you follow the setup in naza assistant. when you put the mouse to a setting, the right side has an explanation. ch7 becomes the mode ch, ch5 and 6 are your x1 and x2 in assistant. make a knob,switch, dial to those channels and follow the directions to set it up.

I fly a naza and have used both radios on the same units, have gone through 4 of them now. They have all done how you explain, i just leave in manual, have since i got it last december and have since. i sw somebody post something about bringing it to an idle and stiring the right stick to make...

yea, they come with shims but there not an easy deal to use. it's been a long time, but i think you have to ream the front of the prop out a little, preserve the precission hole at the back and slide the adapter on, thin one and it helps to shafe it, i used an xacto knife and lightly spun it in...

No problem i slept on a problem and it's still a problem,,,,, back to plan A. it usually works for me no problem having it setup anyway you want the switch

yes...... adjust your subtrim till atti lights up with the switch in the middle, make sure to hit the middle of where it lights up. if it stays blue 10 clicks, go back 5..... then open your end points and adjust them to make gps and manual light up respectively. if you want the switch the other...

now your talking about two different voltages. in a voltage cutoff setup, it is under load and the voltage would sag depending on the ir and the c rating. you want your battery no lower than 3.7 volts a cell when you put it on your charger. none the less, 2 minutes? if you charged a pack all...

Your killing the battery. they both do it cause you killed em both. Try discharging so it sits with no load at 14.8....... after the first time you took it past that, you damaged it. every flight after just kept driving the nail in the coffin. Your batteries are all fried. if you have a...

good info. i fly over water, alot....... what is cut water reflections form headings? this had one on it, but just a little piece of plastic. i'd set the lens cover on the lcd phone and turn it till it went dark not dark on the phone form the angle it sits on the camera. will the uv filter do...

it's gonna shut with everything on except the props, that'll work.

it's yours if you want it, $20 shipped pm me for paypal info

sold almost all mine, needed more fpv quads

the main rig is assembled. next up before everything gets cranked down and the $2 anti jello mount goes on i'll go through and program the osd. i'll capture the live feed to a video for that part and try to explain it. It's pretty simple, has one button, you push it fast for next, hold it down...

between that and fine tuning the gps for forward being forward, this thing really grew up on me....... it started like a little toy and now it's pretty dam cool and all matured in what, 8-9 months, amazing...... Can't wait for the osd. I'll be trying to program a ppm signal to this thing in a...

got a brand new 16mm for it heading this way. one more question. do i want or need a polarized filter for all the water flying i do? if so, whats the lighter way to do it?

on sale bottom of page, careful, if you goto the products page it's full price, that price is only on the buy now button on that page http://www.commonsenserc.com/page.php?page=one_deal_day.html

hahaha... sweet. this things all soldered up, rx is wired in. Dam, it could fly if i bolt it together. gonna go do a photo shoot when the sun gets over on the side again and post the end

if your spinning and there slowing/speeding smooth and even your golden, if it shows a tenancy to show speeding up constantly on one side or a really weird look towards one side it's pissed flying all the weight on one/two motor. Sometimes if cg just went a little further it'd smooth out or if...

cool...... your near that kid that bought my kloners 450. he goes to logan on the weekends, but is down near the lake somewhere, dads a dentist in town