Search results

did they all break up, quit? seems like zero participation to any forums, all i see if people complain about wait times like there busy... weird, FAA stomp em?

the vtx heatsink is in the air, sits up just over flush to get a piece.... the cameras have a heat sink too but there buried in foam. the bec's have such a small draw they don't even get warm.sitting at an idle the rig draws .7 amps......

it all runs cooler than they do on my multi rotors... constant air blows across em, even in the heat of the heat like im in. the camera runs warmest but the video tx that gets 150 degree on my multi only runs 10 over ambient on this. I have had problems burrying esc's, they gotta have air over...

I've got a gig coming up and wanted to share the airframe with you guys. This one just carries sensors so no need for camera mounts. It's alot more aero dynamic than anything i've built before in search of efficiency. the kit is a ritewing Zephyr z60 quadspar, then i also quad spar the wing to...

hoverfly was working on something similar.

ours are alot like the set he posted to this thread but casted in a mold instead of cnc so were able to bring the complete kit cost down to less than what the ends would cost and from our end, the cf is the most expensive part. i hear ya. We have backpacks like you showed but the disco sits...

that thing is prestine........

i'd think 1000 kv motors would over amp...... simonK is nice firmware. Has endpoints all set, won't lvc on you. The real deal if you want performance is nfet esc's. the 960 leopard i use are pretty much the same thing and i know what you mean, it's just that extra weight isn't helping your deal...

the x8 would tidy up the isue as well sticking with the smaller footprint but the current arms available arent strong enough. we got some coming that will and are and is.....

jfro, i was turning towards home then noticed the road and shot in to the tree. it was a maiden and i had just been locked on them tracks. it's like running a sprint mentaly this is the raw footage, think the warp added a little frame loss there. If my $30k skyjib shot that well i could sell em...

J, this one has plush 40 amp, mainly cause there cheap and handle 6s. no firmware upgrades it is a polar pro nd filter. it acts as a makeshift layer lens as well. benefit is it's like sunglasses in the sun and there glass so they can be easily cleaned. i have polarized too imagine your asking...

thanks dude. miss that old fart. He had some stories, let me tell ya. he finished out the war, came home and on his way landing at Van Nuys hit wind shear and it flipped it over 200 mph and wadded it up hard. burned 80% of his body. needless to say he gave up on the whole test pilot thing. he'd...

that was behaving around 25-28 amps... i see so much sag from them zippy compacts they scare me off around 13-14 minutes. the voltage drops about 1.5 volts full forward on the elevator stick and it hits 50 amps somewhere around 50-60mph this was the first flight, naza wasn't calibrated but i...

all atti flying. these motors rip, more power you give naza the further she'll lean into the wind...... these are 400 watts a piece, 1600 watt rig. disco pro is the bomb

it's rolling left and right making a yaw affect through a 2 axis gimbal... weird. heres the entire flight, it was manual mode flight till 5 minutes 80 inches and 8 lbs 5 oz throwing out of my hand...... it's almost like a 3d foamie leaving,,,,, clinch the *** cheeks everytime it leaves my...

for those that don't know me and the whole punkie thing, this was my Grandfather. pretty much raised me and is the drive that's my fascination with flying the first one (c model) ran out of fuel on the way home,,,, Weird thing happened, had ruby adjusted to let through tilt and roll...

there is no mods, bolt and fly. We got it all dialed in heres some pics of my stocker kit i've been flying vid i made with it the other morning

that's a narrower fov,,,, crazy quality for such a small footprint

thanks for hooking us up G.....

naza gimbal controller is for the old school (as of last winter) servo gimbals. brushless gimbals have or need a seperate BGC or brushless gimbal controler. honestly for that size airframe by the time you get done loading it down with what it takes you will get it over weight with a nex or the...