Search results

Selling a brand new never used DJI iOSD Mark II. $200 + $7 shipping within the USA. contact rory"at"minefilms"dot"com

will an iOSD mini work with an A2?

I have a friend who uses his H14 with the Red Epic and Canon 5D and just loves it. He will also be getting the GH4 to replace the 5D soon. If you have any questions about the H14, let me know.

Our new aerial reel with a mix of Red & Gopro. Passion = Life Mine Films www.minefilms.com

Thanks Ed. Who makes a professional 5.8ghz transmitter that has telemetry ?

thanks news to me. I always thought Lighbridge has to take over your RC as its drowns the signal so you have to run everything through the Lightbridge and hence loose 360 Pan as the cable has go from Camera to Lightbridge to A2 and you the gimbal operator has to be tethered to the pilot. Where...

Anyone know if you can you the Lightbridge and still get your Futaba telemetry? or do you have to use the A2's built in receiver so you loose telemetry?

been a busy summer... https://vimeo.com/105933443

Solved my issue. I wasn't doing the mode change correctly on the R7008SB receiver. You have to hold the link/mode bottom then power it up to get it into mode selection and select 2 blinking red led for Mode B then you have to press and hold down the mode bottom for 2 seconds to lock it into...

anyone know how to get this working? I keep getting "RC lost" in the assistant even though I have a green light on my R7008SB receiver. Do you have to link the R7008SB to the A2? How do you do this?

Hi Scott could you let me know how you installed it and got it working.

I can't seem to get the A2 to see the RC signal on my SBUS receiver. I have my R7008SB in Mode B with channel 8 being the SBUS port and I’ve plugged it into the A2 from 8/SB to X2 on the A2. I’ve linked my 14SG to the R7008SB and have a solid green light and I’ve selected D-Bus in the A2...

Is it possible to plug in the Futaba voltage sensor directly to the A2 or do you have to have the Futaba telemetry enabled receiver for such shenanigans ?

I have the following for sale... 6 x 1205-0064 Boom Bracket Inner SkyJib V2 = $8 3 x 1205-0100 Engine Mount Bracket SkyJib Dimple Black = $25 4 x 1305-0032 Boom 1.5mm L=540mm OD=20mm - Matt - Ti = $200 1 x 1405-0370 SJR Landing Gear Plate 440mm Clearance = $50 6 x 1106-0100 Crash Cage Arch...

The A2's that I've used have the Can1 & Can2 so tight and secure from the pressure of the ESC's plugged in that it pushes everything super tight. I actually have to use pliers to take the ESC's out first before it loosens up enough to take the Can1 & Can2 cables out. What is with the shoe goo-ing?

Would love to be wrong. Show me this working at a lower attitude with a camera payload. And show me this working with a Coaxial setup. Having a parachute system that worked would be amazing but the reality of it it doesn't when you have a payload on and are flying low altitude which is what...

The two wires leading off the PDB are for plugging in 2 batteries to get twice the mAh. The centre plug is a Xt60 for plugging in a flight controller and powering it from the PDB. This unit has been wired ready for the BEC Gyrphon sell if you want to go that route.

a parachute needs time to open and on most film production shoots you don't fly high enough to get any use out of a parachute. Low altitude flying is what the multi-rotor is all about and getting that amazing shot. Besides these parachutes still have the craft descending at a high speed enough...

Selling a used, in mint condition Gyrphon GPD-1000CTP Octo Power Distribution Board. Has 8 bullet connectors on each layer and has dual input wires and a XT90 connector. $70 + $5 shipping within the USA Contact rory"at"minefilms"dot"com

Selling 4 x Boom 540mm for SkyJib-8 Ti-QR. These are brand new never used. $55 each + shipping. Contact rory"at"minefilms"dot"com