Search results

Selling a set of centre plates for a Aeronavics / Droidworx SkyJib 8 v2 Titanium. $180 + $20 shipping within the USA. Contact rory"at"minefilms"dot"com

Selling a set of brand new Tiger Motor T80A ESC's They have bullets soldered to them so are ready to fly. $560 for the set of 8 $15 shipping within the USA contact rory"at"minefilms"dot"com

Hi have 2 x MayTech 40Amp ESC's for sale at $40 each. Shipping within the USA is $6 40A-OPTO with No BEC SimonK firmware (latest as of August 2014) Contact me at rory"at"minefilms"dot"com

Selling... 1 x Aeronavics/Droidworx SkyJib 8 QR Ti (Quick Release Titanium) 8 x Tiger 3520/11 motors 8 x Tiger Motor 80Amp ESC 8 x 15x5 Tiger Motor Carbon Fiber Props 1 x DJI A2 Flight Controller 1 x iOSD MarkII 1 x Power Distribution board with built-in BEC (12v & 5v) $5000 (USD) This craft...

I have a Savox SA 1283SG digital servo and I can't get it to travel more than 45 degree rotation. I can move the servo motor with my hand and tell there is a full 90 degree rotation but regardless of my end-point settings I can't get the servo to rotate the full 90 degree. Does this digital...

Selling a set of 8 x Tiger Motor U7 420k motors. Flown a few times but in excellent condition. Shipped in the original boxes. $960 + $20 shipping within the USA. PayPal payment. Email rory@minefilms.com

I have 8 x T70A Pro ESC's for sale, these are brand new, never flown. They have bullet connectors soldered on and ready to go. $100 each with free shipping within the USA. contact me at rory"at"minefilms"dot"com

Selling brand new Carbon Fibre 15.5 props by Tiger Motors. I have 5 pairs. Never flown, totally unused. Only opened one box to check them. Clearing my stock to release funds. $340 for the 10 with free shipping within the US. Please contact me at rory"at"minefilms"dot"com

Selling my MT3520/11 motors which have been on my SkyJib 8 They have about 20 minutes flight time on them. Great motors, just moving my stock for other gear They come with short shaft adaptors which cost $6 each. I have 8 of them and selling them for $65 each. Will offer free shipping within...

I'll be at NAB with the gStabiH14 gimbal system. - Designed for larger camera such as the EPIC. - 14lbs Payload (6.4kg) - Fast setup time with quick release clamps( no fighting rotating axis ) - Wifi control with iPad & Android + PC & Mac - JoyStick control - GPS horizontal drift correction -...

Selling ultra thin Epic/Scarlet LiPo cables to power the camera from a LiPo battery. These cables are design to be super flexible so that don't get in the way of the gimbals movement and allow it to rotate and move freely. Stiff cables push and pull the gimbal and stress the motors and result...

Futaba R7008SB - 8 ch + Sbus Receiver New, never used. $120 with free shipping within the USA and Canada. Contact me at rory"at"minefilms"dot"com

Looking to purchase Gryphon GPD- 1000CTP and GSR- 5030DM

I have a DJI 900mhz Data Link LK900 for sale. Its brand new in box and never been used. $300 with free shipping within the USA. contact me at rory"at"minefilms"dot"com

any else have an issue with the DJI iOSD mark II not giving you data from a DJI A2? I'm not getting any live data such as voltage, altimeter and gps. I've tried plugging it in in the correct port on the A2 chain, as mentioned in the A2 manual but no data on the iOSD is working.

I've setup my A2 and think I have everything sorted and am ready to fly, only I can't start the motors. I can test them and they test fine but when I try start them with the CSC nothing happens. I'm a Futaba T14SG and using the A2 receiver. Everything is setup and seems to be working expect...

Brand New never used Futaba R6014HS for sale. $125 with free shipping with in the USA. Payment via PayPal.

So I've set my FailSafe on my Futaba T14 and everything seems to work in the A2 Assistant Software. But when I turn the T14 off to test if the FailSafe will kick in from lost of signal from the transmitter it doesn't go into FailSafe on the A2 software. This doesn't seem right. How do you get...

I managed to setup my A2 and T14 brilliantly, the port mapping feature is really handy. The one issue I'm having which I can't seem to solve and I'm hoping you can help me… The 3 way switch SE on the T14 is set to control my FailSafe through the A2 mapping but it also seems to adjust the...

What is the deal, should I braid the motor wires on my multirotor build (Octo) or should I not? Braiding makes the wires shorter but isn't a good think with long boom arms.