Search results

I have one of the naza gps units identified in the time range of the DJI recall (suggestion), and am having a problem with my quad wantingn to wander off on its own and seems to require significant input to keep under control and return. Could this be related...

I have not been able to get satisfactory results from my new Naza-gps setup. Its a 450 Flamewheel. When I have all satellites locked and am flying in gps mode, it will hover stable for a moment, and them begin to wander off, causing me to have to use increasing amounts of cyclic (or whatever...

I just installed and setup this Naza and when I have test flown it to adjust gains, it seems to take off in one direction or another when not being forced in the other direction. It also reacts very strongly to mild throttle and cyclic input causing to go out of control quickly and I wonder...

I haven't yet gotten it completely installed, but I noticed first thing that there was no documentation or license codes in the box anywhere. Am I missing something, or does the naza not need them like the WKM did?

I am about to purchase an FPV setup. I have a Flamewheel with Naza GPS. My plan is to use my Gopro with a 5.8 Immersion 600mw tx, and a Duo5800V2 Rx. I wouldn't use the built in 5.8 receiver in the headset, but how could I use it without cables hanging down? Also, what is the battery...

There are a few different models of fatshark's out there, and I am having trouble deciding which is most appropriate for FPV. About ready to buy, and I don't want to choose poorly. Attitude SD Dominator Predator V2 Aviator Edition ?!?!?!?!? Thanks

I bought this a few months back, but I never used it once. It was a bit of an impulse buy, so now it can go to someone who will actually use it. HS785HB servo 3-1/2 rotations (pan) & HS645MG Servo (tilt) (Recommended for EagleEyes w/360 panning) Here is the web page for it -...

COMPLETE XA HEXA with DJI WKM Wookong and XA gimbal + spares I built this Hexa to fly around my GoPro camera, but I am moving up to a larger heli, so It is not needed. It has had very little use, and is perfect condition. It flies for a little over 10-12 minutes with two packs. It can also...

I put two flights on this frame after assembling it, and decided to go with the Hexa instead. I removed the electrics, so it's only a bare frame. It has all the stock parts except the yellow decals. it is this exact package below...

I have a Bantam BC6 charger that is giving me frustration. I fly my hexa with a pair of Turnigy Nano 3s 5000mah batteries. About every other flight I balance charge them individually, the other times in parallel. The last few times with one of my newer batteries my charger is not evenly...

I am having trouble getting a smooth spool-up on my Hexa with QuadDancer QD1100B motors. I recently installed new Turnigy Plush 30A escs, and I think the problem might be in the high amperage capability of the escs, compared to the much lower demand of the motors. It is very hard to take...

I just started flying my XA Hexa/WKM. I noticed that the motors don't spin up evenly, and one or two won't even move until the other 4 are almost lifting off. It takes off controllably with steady throttle, but still seems odd. Another thing, it seems like the motors are cutting out for a...

I could use a prop recommendation for my XA Hexa. I have the Quaddancer QD1100b motor from CNCheli, and have been using the 10x4.5 props he also sells. http://www.cnchelicopter.com/servlet/the-1834/QD1100B-upgrade-motor-for/Detail and these props - I really don't like these motors at all...

I am getting ready to install the Turnigy Plush 30 escs on my XA Hexa, and am thinking there might be a better way out there to distribute power then how I've done it in the past few multis. Typically I would solder together 7-8 JST female connectors to an inch or two of 12 gauge wire with a...

I have an XA hexa set up with the QuadDancer qd1100b motors recommended by CnCHeli, and DJI WKM system. What is the minimum C rating I should be looking at running with a multirotor of this size? I am currently using Nano-tech 35-70c and they seem to work well, but If I could go Down...

I assembled my Flamewheel last night and had a wonderful flight this morning with my Gopro attached. The DJI WKM kept it very stable and smooth. After a few flights I experienced a mishap. At about 30 feet over grass, it suddenly tumbled out of the sky. Subsequent flight this happened...

I am continually dissapointed with the quality of the motors I am sourcing for my XA models. First I received a motor with my XA X650 V4 that had a visibly broken winding right out of the box. Another blew off the E-clip within three flights, and there seems to be none available from the...

I am looking around for a short little lightweight extension I can leave onboard and plug a standard USB cable into, but I can't tell what type of plug connector is on the side of the MC. I thought it was a mini-USB, but it's a little different. Anyone know?

Im setting up my Xa Hexa with Dji wkm, and am curious what is the preferred method for proper balancing? Also, I am assuming most folks are usin a consistent battery load, vs sometimes one pack, sometimes two.... I have it flying, but am now chasing down the little issues affecting flight...

I have finally got my XA Hexa flying, although not too well... THe current issue that I am dealing with is my batteries. I have been using two Eflite 20s packs (1800 and 2100 mah) and a Tenergy 25c 2200 pack. I installed the Chestem 3 in 1 BEC with voltage monitor, and even when the packs...