Search results

When I travel with my Larger Octo. I take the landing gear/Gimbal off by removing the 4 bolts on the Gear rail Bracket. I pack that whole assembly into a seperate box. Then my copter, Radios, Charger, and power supply go into these cases. They are not cheap, but they will protect your $15k-20k...

WOWWWWW What a great trip. There was so much to see and do, that I should have stayed at least another day. I spent most of yesterdayin the Droidworx booth, Helping Linda out so she could take a break. That turned out to be amazing, I had a great time chatting with everyone, anda nswering their...

GYRO TAPE I have used Zeal, and have recently Switched to Beast X gyro tape. The Beast X seams to work better for me, and it only costs $6 for 4 squares. I use it on my FC's and on my Receivers. The Zeal seamed to have a little more wiggle (if that makes any sense).

Sorry about that guys. I took the post as him asking advise on where to get good service and such. I was just offering another option. Looking back, I should have definently sent it by PM. Again, sorry about that. I edited my original post.

I am going to be meeting with Sidney and Kimberly at the show. If I cant find a decent ticket, I may just fly my Cessna in. Either way, I will be arriving Monday. Should be a good time for sure. I will be sure to snap lots of pics for you guys :) Would be cool if a few of us from the forum...

Wow, that is an awesome post. I really appreciate thepositive feedback. When I started into multirotors, I had the worst experienceever. Needing a copter in a hurry for an Aerial gig, I dropped close to $15k ona RTF Hexa. It flew for approx 7min before going completely bonkers andcrashing into...

PM sent

Awesome Bart, Very nice Copter and gimbal combination.

Thad, when switching from Atti to Manual, I also get a little jump. I do make a note to myself to bring the throttle down a little bit before flipping it into manual. I have been flying the 550 allot today, trying to replicate that twitching problem. So far no luck. I'll let you know as soon...

You can cut the little tab off with an xacto knife or razor blade. Then to plug into your graupner, there should be a diagram of the wire layout. Usually +/-/Signal. With The wires coming from your wookong, the ORANGE wire is signal. Just make sure the Signal wire is plugged in to the signal...

Thad, I have been running the Common Sense supply for over a year without a single problem. With everything I do, I like to buy right and buy once. There is certainly is not anything wrong with getting that other power supply. I just do not see the real advantage of it. I charge Dual lipo's all...

I hope this descibes it correct. First, you need to select an ACRo model in your Radio. Next you need to Assign the F-Mode switch on your radio, to an Aux ch of your receiever. To do this, Hold down the SCROLL WHEEL on the DX8 while you turn the radio on. Scroll down till you see SWITCH...

To get it to show properly for the GPS and M position. Put the switch in the desired position. Say GPS, then go to your Servo screen-Travel. Adjust the travel End Point so that it will make the arrow fall on the GPS section. Then put the swith to Manual, and adjust the travel in that direction...

Did you mean to say "But the positions are NOT CORRECT"? If it is showing the positions opposite in the software, when flipping your mode switch. Then you can simply reverse that channel in your transmitter. Go to the Servo Menu, the select the REVERSE option. Then select your FMODE channel...

The props are being bored to the following 10x5 8mm 12x5 6mm 13x6.5 6mm If you need a diffrent bore, let me know and we can get you a custom set on order. Take care, Patrick AerialMediaPros.com

Ill have your XOAR's Sooooooon ;)

Check out AerialMediaPros.com (Under the Store section). Then give me a call at 888-557-6791. I will answer your questions, and go over some options with you. Take care, Patrick

Hmmm You have me stumped on this one. I assume the flashing yellow is because your in Atti mode. If it is flashing rapidly that is something else. I had unplugged my throttle cable to the reciever once to do something to program some ESC's, and it flashed rapidly because there was no signal from...

Did you try reinstalling the Software and Drivers. Do you havethe latest Software. If not, Here are all the downloads http://aerialmediapros.com/store/support.php?osCsid=2d798208c2b8976c2751a57433814133