Search results

Nice, i have graupners on my F550 wookong, just shot some video today with the gopro slung on a xaircraft gimble, no vibrations at all! But, always a but lol im unsure as i have the gains where i need them gimbal settings aswell. Right now its 110,110, 120,130. Atti at 80,80 Ill post my...

Like it says, im runnin a 4s 4000, on 10" graupners, 30 opto on a f550 with xaircraft gopro gimbal/gopro. AUW Is unknow, i havent done the math nor do i have a scale Sent from my GT-I9100M using Tapatalk

Guys, could someone shed some light for me on a 3s parallel setup. Do my batts have to be smae brand? Same mah, i have a 5000 and 5400... Might grab another 5000 of same c if need be are they wired with a y adapter Sent from my GT-I9100M using Tapatalk

Final deal... Not bad introduced a bit extra play but i shot a quick vid tonight and its good Sent from my GT-I9100M using Tapatalk

I ended up not doing any drilling, cut a piece of aluminum and mounted it using supplied openings spaced down 3/16" and drilled the aluminum to suit the gear, looks and works great ill post a pic after work Sent from my GT-I9100M using Tapatalk

Gunter, did you use plastic screws aswell? Im ready to drill my 550but im concerned about the positive shorting to the negative plate on the bottom, because id need to use metal screws... Sent from my GT-I9100M using Tapatalk

Ed, will this work the same on a hexa? Sent from my GT-I9100M using Tapatalk

You mean if i dont grind the black off it wont short.... Nylon washers, should do Sent from my GT-I9100M using Tapatalk

Robert, what kind of flight time on 4's 5000 with some load Sent from my GT-I9100M using Tapatalk

Thanx, i can see the outline on each side of the positive and negative feeds but im concerned about it shorting, im going to try and find a piece of carbon plate or aluminum to attach normally on the bottom then drill the mounts in it Sent from my GT-I9100M using Tapatalk

Ive seen john did a build with Xaircraft landing gear under it but i couldnt see in the pictures if he drilled through the distribution part of the board, im doin the same and can only see that there's only enough room for two screw per mount instead of the 4 it would normally use... I could...

Kind of, but i wanted to keep auxiliarys free for gain tunkng and gimbal adjust, can i not mix from my mix switch into gear or wookong u channel Sent from my GT-I9100M using Tapatalk

Im in coquitlam but always looking for others who fly Sent from my GT-I9100M using Tapatalk

Got a mix made so that i get failsafe in gps and manual mode, but i cant figure how to get it to go in failsafe in atti/middle switch position. Ive tried messing with the rate and offset in mix manual with no luck... Am i beating a dead horse. Should i settle witg failsafe activation i. Gps...

I have the wookong all set up with my dx8, but i cant get a mix to work like it does on my naza for failsafe? any ideas

I have the wookong all set up with my dx8, but i cant get a mix to work like it does on my naza for failsafe? any ideas

I CA'd er, thanks Sent from my GT-I9100M using Tapatalk

What do you guys use to attach your wookong gps to the pole.... Aside from the aluminum pieces, what u using to glue stick to bracket Sent from my GT-I9100M using Tapatalk

Hey guys, still not fully sure on this voltage cut off business, im understand the batterys operating voltage and what not, that lipos shouldnt be taken down past 80%, I know how to check for mah usage by running for say 5 minutes and seeing what i put back to get a flight time.... but entering...

I too am interested in these answers,