Search results

Another issue is the balance of the camera in the gimbal: When the USB is plugged in I found that I had to move the balance on the roll motor mount (one at the back) right over towards the tilt motor. The other thing I had to do was to cable tie the wire to the back frame to prevent the cable...

You can only have one firmware installed on the board at any time. If you successfully uploaded new firmware then that is what you have. When you flash to the board it is saved and any old firmware is deleted in the process. One of the issues people do have is that they think they have...

You could try something like THIS from HK. Red on back and blue on Front or whatever configuration you wanted. They will run directly from a RX terminal too so no need for a separate UBEC.

I would hold fire until the WKM arrives before you start trying to pre-empt the connectors you will need. My motor harness came with an xT60 already on. It may be that all you may need to change is the Deans on the harness to an XT60 or just sit and have a think when it all arrives. I may...

The new Zemnuse does appear to be a nice bit of kit and will be able to mount to the bottom plate of the load mounts provided by XAircraft with little modification. Another thing I hav noticed is that there is little or no vibration on the x650 either so no 'Jello'. The WKM comes with xT60...

I always thought that the DJI warranty is void the second you pay...... Has anyone ever had something replaced by them?

I have never used a Zenmuse I am afraid. However, I believe it to be an excellent bit of kit and will plug directly into your setup with all the cables provided with the downlink, iOSD, PMC etc.... However, being 3 axis you will need to have a separate TX and a second person. Also the landing...

Once airborne you will notice the stability and spare power available with the pro compared to the Value.... The name gives it away. You get what you pay for. Can't wait to see how the build goes. If there are any problems I should be able to help as you are building almost exactly what I...

Philippe, My settings on the WKM are below:- 1st Level 2nd Level 14 Voltage 13.4 0.5 Drop 0.5 13.5 Trigger 12.9 I have my Lipo alarm set to 3.4 per cell giving audible warning shortly after the first level is reached, when the voltage drops to...

I have now put Deans onto my Zippy 8000mah 4s 30C Lipos and cycled them 4 times now and the flight times are very good. Even better than they claim on their website of 20 mins with wehight of 1800g (including 4S 5800mAh battery). I am running the 8000mah with a total weight of 2.6kg. That...

Thanks for the heads up on the Phantom gimbal. I haven't mounted it yet because I am waiting for my Hitec 7ch RX then I intend re-configuring everything. One thing I do intend is widening the battery hole and mount a 3300 lipo. I cable tied one to test it and get 17 mins with the old servo gimbal.

Excelent.... Damn frustrating but working it is a quality bit of kit. You may want to drop Rob a line with your ideas. He is normally quite accomodating and helpful. I have three of hos gimbals now. When i mount my Phantom version I will post my findings. One thing he could do is slimline...

From day one my WKM has had gauze and sticky plaster on it and have flown in 20mph wind without a flinch or wobble. The WKM sits in the centre between top and bottom frame plates so is like a tunnel where it sits. (XAircraft X650 Pro Carbon)

No but the requirement for UK registration is to have a first aid kit and fire extinguisher when flying. They also recommend a Lipo safe for storage and transport, serately, charged and dishcharged lipos. Although an electric fire water is recommended because it will limit fire spread and short...

Kellend, I am sorry you are having difficulties with it but every brush-less gimbal requires some setting up. Some use the Martinez board but all use a GUI system, which requires some IT input. Even slick systems like DJIs stuff required software installed, drivers and a GUI interface to...

I concur with Bengit the gimbal is very very good. The Gimbal Information can be downloaded Here:- Gimbal Instructions:- Brushless GoPro Gimbal Upgrade instructions:- Updating and Adjusting the Martinez Brushless Board Driver update if no connection to gimbal with USB:- Martinez Brushless...

Can you connect a simple servo to the same port on your RX and see if the servo behaves the same. If the servo behaves correctly and moves proportionately to the pot movement then there must be something in GUI setup needing altered or the board is indeed faulty. If the servo behaves as the...

Let's hope they do and continue to engineer them to the same German standards and not the sweatshop standards we now expected from many Asian produced goods.

Out of principle I wouldn't buy from Team Blacksheep they are a disgrace to the hobby and have probably caused or at least escalated part of the problem in the US relating to banning AP.

Use Intelligent mode for the reasons above. It would be a little traumatic having the motors cut mid-air.... at least with intelligent mode there are a few seconds before the cut and if they do as long as you raise the throttle above 10% immediately they power on again.